View Poll Results: I am interested in a....
Black Powdercoat Finish
58
49.15%
Clear Powdercoat over Polished
33
27.97%
Paint Matched
27
22.88%
Voters: 118. You may not vote on this poll
Heat Shields for you 05-07 Mustang Intakes
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
Bullitt Member
Joined: October 30, 2006
Posts: 492
Likes: 1
CR... looks good! 
It does look much more beefy. A couple of questions: hows the fit around the ABS lines? Looks like the shroud is up against the lines. Also, will it have any type of gasket/padding on top edges? (to seal against the hood liner). Thx.. nice looking product.
It does look much more beefy. A couple of questions: hows the fit around the ABS lines? Looks like the shroud is up against the lines. Also, will it have any type of gasket/padding on top edges? (to seal against the hood liner). Thx.. nice looking product.
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
When the physical product comes out, it will be away from the ABS lines. It was a little too close, and the tooling has already been altered.
On top, will be sealed as well. The pinchweld that you normally see on K&N kits, etc. will not work, because the air filter sits higher than the seal does. We're going to seal around the top edge, however. You'll see when the final powdercoated pictures come out next week. We will start taking preorders for the J Series on Tuesday.
CR
Tillman Speed
On top, will be sealed as well. The pinchweld that you normally see on K&N kits, etc. will not work, because the air filter sits higher than the seal does. We're going to seal around the top edge, however. You'll see when the final powdercoated pictures come out next week. We will start taking preorders for the J Series on Tuesday.
CR
Tillman Speed
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
No problem, I bust ***** every ones and a while too! You got to!
CR
Tillman Speed
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
Rocky,
After the J & C series, if there is enough of a market for them, sure! I want to improve on little flaws of each original design, make them more rigid, and of course not go crazy on the weight factor... and then have them powdercoated. The C series should be done in 2 weeks, the J is going to be done next week. Depending on how many requests I recieve, I could get that going as early as next week, and ready to ship by early March.
CR
Tillman Speed
After the J & C series, if there is enough of a market for them, sure! I want to improve on little flaws of each original design, make them more rigid, and of course not go crazy on the weight factor... and then have them powdercoated. The C series should be done in 2 weeks, the J is going to be done next week. Depending on how many requests I recieve, I could get that going as early as next week, and ready to ship by early March.
CR
Tillman Speed
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
Thread Starter
Former Vendor
Joined: January 11, 2007
Posts: 2,594
Likes: 0
From: Aston, PA
They're already in production, and the last changes have been done. They should be done this week, and done powdercoating next week. I am going to get a picture of them powdercoated before I take preorders, just so everyone is sure they want to order.
I will start a preorder thread with pics early next week!
We should be able to ship end of next week!
I will start a preorder thread with pics early next week!
We should be able to ship end of next week!