Midwest TMS'ers General Communication Thread
#3004
Cobra Member
I changed the oil and cabin filter in my car. If you have hood struts that mount on the bolt near the cowl, it is necessary to unbolt the bracket for the struts and use the prop rod to hold up the hood. I found that out right away. Oh well, it wasn't difficult to change the cabin filter, it's all good for a while.
#3005
Legacy TMS Member
Join Date: January 9, 2005
Location: New Carlisle, Ohio (20 miles north of Dayton)
Posts: 6,982
Likes: 0
Received 6 Likes
on
6 Posts
#3001..
Hey Justin and Chris thanks for the info on the cabin air filter. I will check mine out to see how dirty it is.
And STD. You said I was only half right about the pinion angle. After reading that article where am I half wrong at? If you are speaking of the race guys leaving the setup angles the same and not nosing the pinion angle downward than I simple just disagree with Joe Heck racing. Simply put the pinion angle will rotate upward under hard lauching. To the point the the driveshaft will slap the under side of the tunnel. I would think it would be more important to angle the pinion down on the race car but.....
Hey Justin and Chris thanks for the info on the cabin air filter. I will check mine out to see how dirty it is.
And STD. You said I was only half right about the pinion angle. After reading that article where am I half wrong at? If you are speaking of the race guys leaving the setup angles the same and not nosing the pinion angle downward than I simple just disagree with Joe Heck racing. Simply put the pinion angle will rotate upward under hard lauching. To the point the the driveshaft will slap the under side of the tunnel. I would think it would be more important to angle the pinion down on the race car but.....
Last edited by 70MACH1OWNER; 3/18/08 at 03:31 PM.
#3006
Legacy TMS Member
Thread Starter
I changed the oil and cabin filter in my car. If you have hood struts that mount on the bolt near the cowl, it is necessary to unbolt the bracket for the struts and use the prop rod to hold up the hood. I found that out right away. Oh well, it wasn't difficult to change the cabin filter, it's all good for a while.
#3007
Shelby GT500 Member
Join Date: October 9, 2006
Location: It's tough in the jungle !
Posts: 2,758
Likes: 0
Received 1 Like
on
1 Post
The basic formula for determining the set start point for setting the angle of the Shaft! Its absolutely crucial to match the angle of the pinion flange to Transmission output flange ! then from that point go about 1 to 2 degrees beyond the trans flange measurement, 2 degrees for a common street set up as yours, the more appropriate setting for me would 1 to 1.5 degrees considering all the after market components I have! there is NO set angle for every application. the perferable track setting has been found to run TO flange at the same setting as the pinion flange ! Scott track guys are not running the sloppy suspension components that come from the factory! Considering Joe Amotto has had more track wins than most guys have had orgasms he might have some insight in to it!
Last edited by blkstang06; 3/18/08 at 03:49 PM.
#3008
Legacy TMS Member
Thread Starter
The basic formula for determining the set start point for setting the angle of the Shaft! Its absolutely crucial to match the angle of the pinion flange to Transmission output flange ! then from that point go about 1 to 2 degrees beyond the trans flange measurement, 2 degrees for a common street set up as yours, the more appropriate setting for me would 1 to 1.5 degrees considering all the after market components I have! there is NO set angle for every application. the perferable track setting has been found to run TO flange at the same setting as the pinion flange ! Scott track guys are not running the sloppy suspension components that come from the factory! Considering Joe Amotto has had more track wins than most guys have had orgasms he might have some insight in to it!
Dang, you been watching Oprah again?
#3010
Legacy TMS Member
Join Date: January 9, 2005
Location: New Carlisle, Ohio (20 miles north of Dayton)
Posts: 6,982
Likes: 0
Received 6 Likes
on
6 Posts
The basic formula for determining the set start point for setting the angle of the Shaft! Its absolutely crucial to match the angle of the pinion flange to Transmission output flange ! then from that point go about 1 to 2 degrees beyond the trans flange measurement, 2 degrees for a common street set up as yours, the more appropriate setting for me would 1 to 1.5 degrees considering all the after market components I have! there is NO set angle for every application. the perferable track setting has been found to run TO flange at the same setting as the pinion flange ! Scott track guys are not running the sloppy suspension components that come from the factory! Considering Joe Amotto has had more track wins than most guys have had orgasms he might have some insight in to it!
Well,
I only have one thing to say .........."you pay your money and take your chances" Lordly I hope you don't mind f**** the cams like this.
Do it or forget it!!!!
#3011
Shelby GT500 Member
Join Date: October 9, 2006
Location: It's tough in the jungle !
Posts: 2,758
Likes: 0
Received 1 Like
on
1 Post
Hey, can someone translate this for me ! I don't speak Buckeye.... I don't care how much we argue its all in good fun ! and yes I am already mind bone'in the cams
Last edited by blkstang06; 3/18/08 at 06:06 PM.
#3018
Legacy TMS Member
Join Date: January 9, 2005
Location: New Carlisle, Ohio (20 miles north of Dayton)
Posts: 6,982
Likes: 0
Received 6 Likes
on
6 Posts
How much rain have you gotten over there? We have had 3.25 inches as of 5 am this morning and are supposed to get 1-2 more today. The Dayton area has 4 rivers running thru it Little Miami, Great Miami, Mad River and the Stillwater River. They are all forcast to go over flood stage about 7 pm tonight. Glad I live on a hill. It's bad around here.
#3019
Cobra Member
I know all that snow melting didn't help much out there either, all that water needs to go somewhere. I drove the Escort through a few huge puddles in the road when all the snow here was melting. It's just about all gone now though.
#3020
EUREKA, I've done it. I got the job that I have been interviewing for. I feel like dancing, dancing, woo dance the nite away.
Actually making more money than in my previous job. Oh, happy day I hope my excitement is coming through.
Actually making more money than in my previous job. Oh, happy day I hope my excitement is coming through.
Last edited by Eleanor Dreaming; 3/19/08 at 10:02 AM.