What did you do to your '10-'14 today?
#2782
FR500 Member
#2784
2013 RR Boss 302 #2342
Join Date: March 6, 2012
Location: Lancaster, PA
Posts: 11,719
Likes: 0
Received 2,226 Likes
on
1,661 Posts
Originally Posted by TripleBlack14
We never followed through on some kind of cruise or attending an event halfway between Lancaster and this area of Jersey like we talked about. Lets try to figure something out for this season if we can.
Late last October I attended a NE Regional SAAC show in Macungie that was open to all Mustangs (and Fords). Mustangs, Shelbys, Bosses, Mach 1's galore...all years, and each generation and variant had it's own class. It was peer judging only and I snagged a 2nd Place in my class. I didn't decide to go until the last minute due to weather concerns. I should have PM'd you.... my apologies. Not sure if the SAAC is doing it again this year. I'll try to find out and let you know.
On April 24th my Mustang club is doing an all-Ford show at a dealer in Sussex County in the same general area as the Chatterbox which I think you said you're familiar with. I realize that's a major haul for you, but I'll throw it out at you anyway. It is an inaugural event so I can't make a prediction on turnout.
This was my fav Gen5 Boss at the Shelby show....
Late last October I attended a NE Regional SAAC show in Macungie that was open to all Mustangs (and Fords). Mustangs, Shelbys, Bosses, Mach 1's galore...all years, and each generation and variant had it's own class. It was peer judging only and I snagged a 2nd Place in my class. I didn't decide to go until the last minute due to weather concerns. I should have PM'd you.... my apologies. Not sure if the SAAC is doing it again this year. I'll try to find out and let you know.
On April 24th my Mustang club is doing an all-Ford show at a dealer in Sussex County in the same general area as the Chatterbox which I think you said you're familiar with. I realize that's a major haul for you, but I'll throw it out at you anyway. It is an inaugural event so I can't make a prediction on turnout.
This was my fav Gen5 Boss at the Shelby show....
#2785
Legacy Tms Member
#2786
Roush Forum Stalker
That's awesome. The roads are actually clear of snow and wet. The snow is all gone in these neighborhoods. Just some sand on the edges of the road.
#2787
Legacy TMS Member
Took my new rear spring perches apart and installed them the right way, while also adjusting them up a tiny bit more, so the right rear measurement from the ground to the top of the wheel opening is 29", left rear almost a half inch more, but the driver side has always been higher ... I'll adjust it down in a few more days, bring it down a 1/4" or so.
Then, drove it!
Took it out to lunch with the girlfriend, then a nice little half-hour drive the long way home.
No rubbing!
Then, drove it!
Took it out to lunch with the girlfriend, then a nice little half-hour drive the long way home.
No rubbing!
#2788
The Steeda aluminum Ds is in. When the exhaust pipe were removed, the installation was very easy. I just wish my new DS was a little lighter.
The car feels more responsive and OI love the fact that the clunky sounds when shifting gears have disappeared by about 70-80 percent.
I also like to mention that Steeda customer care is top notch. When I ran to small confusion during the install, TJ sent me a PM quickly to help out.
The car feels more responsive and OI love the fact that the clunky sounds when shifting gears have disappeared by about 70-80 percent.
I also like to mention that Steeda customer care is top notch. When I ran to small confusion during the install, TJ sent me a PM quickly to help out.
#2789
Bullitt Member
I installed some engine bling, from Emblem Pros. The "Powered by Ford" on the coil covers. The "32V Tivct", and a nice "coyote" emblem on the engine cover. It looks more complete now.
#2790
Legacy TMS Member
The coil cover inserts ... on their site they say that the inserts will be raised, they seem to be slightly raised, are they really?
Any chance you can get some nice close-ups of the covers, maybe from above and also at an angle to see if they are raised and how much?
I've been looking to get the EmblemPros kit for years, but still can't get some really good pics of just how well they fit
#2791
Bullitt Member
Gabe, the coil cover lettering is almost flush, where it should be. Maybe slightly above the cover, but hardly noticeable. The 32 tivct on the front seems to be raised slightly more however. I will get some closer shots for you.
#2793
Shelby GT350 Member
The Steeda aluminum Ds is in. When the exhaust pipe were removed, the installation was very easy. I just wish my new DS was a little lighter.
The car feels more responsive and OI love the fact that the clunky sounds when shifting gears have disappeared by about 70-80 percent.
I also like to mention that Steeda customer care is top notch. When I ran to small confusion during the install, TJ sent me a PM quickly to help out.
The car feels more responsive and OI love the fact that the clunky sounds when shifting gears have disappeared by about 70-80 percent.
I also like to mention that Steeda customer care is top notch. When I ran to small confusion during the install, TJ sent me a PM quickly to help out.
#2794
Legacy Tms Member
My first round of engine detailing since Ratageddon. I noticed that the strut brace has little scratches from my little friends. I'm hoping I can buff them out. If you look closely you can see where the little buggers were chewing up my firewall insulation.
I'm still deciding if I should replace it. It's minor and most people would say I'm crazy since its in the engine bay but I don't care. It bugs me.
I sprayed the engine with a Stop the Rodent spray. Does a good job and it it works it'll be something I continue to use.
I'm still deciding if I should replace it. It's minor and most people would say I'm crazy since its in the engine bay but I don't care. It bugs me.
I sprayed the engine with a Stop the Rodent spray. Does a good job and it it works it'll be something I continue to use.
Last edited by VidPro; 2/28/16 at 11:21 AM.
#2795
Legacy TMS Member
Took it through a quick touchless wash and drove it to a Mustang club meeting.
It was one of only 2 Mustangs there, so these pics are from the drive home
It was one of only 2 Mustangs there, so these pics are from the drive home
Last edited by Gabe; 2/28/16 at 01:47 PM.
#2796
Roush Forum Stalker
#2797
Legacy TMS Member
#2798
Legacy TMS Member
#2799
Roush Forum Stalker
#2800
Legacy TMS Member