'13-14 Cluster into '10-12 car (with TrackApps) retrofit
Shelby GT350 Member
Joined: September 11, 2006
Posts: 2,349
Likes: 5
From: Cumming, GA
Too many hobbies. I also have a few Motorcycles and Firearms as well ...
Last edited by dmhines; Jun 1, 2014 at 08:52 PM.
Shelby GT350 Member
Joined: September 11, 2006
Posts: 2,349
Likes: 5
From: Cumming, GA
Nice ...
I got some VIDS here too ... instead of filling up the thread.
https://www.youtube.com/user/dmhines/videos
I got some VIDS here too ... instead of filling up the thread.
https://www.youtube.com/user/dmhines/videos
GT Member
Joined: May 31, 2012
Posts: 182
Likes: 1
From: Indianapolis
Nice ...
I got some VIDS here too ... instead of filling up the thread.
https://www.youtube.com/user/dmhines/videos
I got some VIDS here too ... instead of filling up the thread.
https://www.youtube.com/user/dmhines/videos
ok everyone nothing to see here. Move along, move along...lol
now back to our regularly scheduled programming.
Last edited by crazietj; Jun 1, 2014 at 09:14 PM.
Mach 1 Member
Joined: March 1, 2007
Posts: 669
Likes: 5
From: Kansas City
Its to dangerous to put any type of module between the ABS and PCM for relaying/manipulating data.
So adding a accelerometer would be easy. Just have to silence the ABS module on some data somehow. Not an easy task.
No worries, we will get er done
-Matt
So adding a accelerometer would be easy. Just have to silence the ABS module on some data somehow. Not an easy task.
No worries, we will get er done
-Matt
Shelby GT350 Member
Joined: September 11, 2006
Posts: 2,349
Likes: 5
From: Cumming, GA
Yes .. much better looking for sure. It is a little glossy .. should be flatter like OEM since there is a sheen when sun shining on it. Also - all the symbols are accurate but they use a texture on the clear plastic so when the light shines through it makes them not appear as nice and crisp as factory.
V6 Member
Joined: April 2, 2014
Posts: 83
Likes: 0
From: CA
V6 Member
Joined: April 2, 2014
Posts: 83
Likes: 0
From: CA
So I just installed the new ABS module and reflashed my PMC to DR3A-12c650-AJD. After that I did the PMI of the PCM, I ended the session and restarted it to confirm the PMI. It was good and on the VIN screen with mileage I changed my VIN to 2014 VIN and then did the PMI of the ABS module. Something happened, but it asked me for the as built which I typed in (016A, NON SVT PP GT500). Then it asked me for the .ab file cause it was unable to locate it on the network. So I downloaded it and placed it in the calibration folder and confirmed it was in the folder with the tick mark. It did it's thing and the ABS light went off. Then I did a DTC check and all I had to do was the YAW sensor. I did and cleared all the DTC's and the were all gone. I included a picture of the files it downloaded before asking me to download the .ab file, as I always keep this window open ever since Dan told me to. This folder was blank before the PMI on the ABS module, fyi.
Last edited by BlueEyedSnake; Jun 3, 2014 at 08:55 PM.
V6 Member
Joined: April 2, 2014
Posts: 83
Likes: 0
From: CA
Oh sorry, yeah it's all good. I just need a tune or calibration file to drive the car. But all the lights are off and there are no DTC codes.
Know I need to find out way my tact even after being warm won't turn off the red light at 6,250 RPM's. Launch Control won't work until that light goes off and the rev limiter is 7,000 telling the PCM that the vehicle is at temperature. Any idea's anyone ?
Know I need to find out way my tact even after being warm won't turn off the red light at 6,250 RPM's. Launch Control won't work until that light goes off and the rev limiter is 7,000 telling the PCM that the vehicle is at temperature. Any idea's anyone ?
Mach 1 Member
Joined: May 29, 2012
Posts: 791
Likes: 23
From: Westminster, CO
Oh sorry, yeah it's all good. I just need a tune or calibration file to drive the car. But all the lights are off and there are no DTC codes.
Know I need to find out way my tact even after being warm won't turn off the red light at 6,250 RPM's. Launch Control won't work until that light goes off and the rev limiter is 7,000 telling the PCM that the vehicle is at temperature. Any idea's anyone ?
Know I need to find out way my tact even after being warm won't turn off the red light at 6,250 RPM's. Launch Control won't work until that light goes off and the rev limiter is 7,000 telling the PCM that the vehicle is at temperature. Any idea's anyone ?
LEXiiON
