What did you do with your Mustang today?*
Roush Forum Stalker
Joined: March 9, 2013
Posts: 11,140
Likes: 1,749
From: Massachusetts
(I actually want a CTS-V. A sedan and a coupe please! lol
)
Super Boss Lawman Member
Joined: October 16, 2012
Posts: 4,414
Likes: 215
From: Vancouver BC
Looking amazing as always Tony. Good thing the film crew guild isn't on strike!
I liked the CTS too, but i'm looking towards a new vehicle next summer to use for commuting without any gas. This one (ELR) is comparable to the Camaro SS power wise
Reminds me of a Lambo slightly too.
I liked the CTS too, but i'm looking towards a new vehicle next summer to use for commuting without any gas. This one (ELR) is comparable to the Camaro SS power wise
Reminds me of a Lambo slightly too.
Roush Forum Stalker
Joined: March 9, 2013
Posts: 11,140
Likes: 1,749
From: Massachusetts
Looking amazing as always Tony. Good thing the film crew guild isn't on strike!
I liked the CTS too, but i'm looking towards a new vehicle next summer to use for commuting without any gas. This one (ELR) is comparable to the Camaro SS power wise Reminds me of a Lambo slightly too.
I liked the CTS too, but i'm looking towards a new vehicle next summer to use for commuting without any gas. This one (ELR) is comparable to the Camaro SS power wise
Reminds me of a Lambo slightly too.That's pretty good power wise. Looks pretty cool too for an electric car. Good luck!
Legacy TMS Member
Joined: August 7, 2011
Posts: 5,246
Likes: 567
From: NC
Had some surgery done on the stock H-pipe.
Went from this:
To this:
To this, using 3" stainless steel pipe:
And both sides done:
The power seems the same, the sound seems to have gotten a bit deeper/growlier, and maybe 5-10% louder
For $120 it does a decent imitation of an aftermarket h-pipe I think, while not spending the $300+ that one of those goes for.
Went from this:
To this:
To this, using 3" stainless steel pipe:
And both sides done:
The power seems the same, the sound seems to have gotten a bit deeper/growlier, and maybe 5-10% louder
For $120 it does a decent imitation of an aftermarket h-pipe I think, while not spending the $300+ that one of those goes for.
Bullitt Member
Joined: October 22, 2010
Posts: 354
Likes: 0
From: Indiana
Super Boss Lawman Member
Joined: October 16, 2012
Posts: 4,414
Likes: 215
From: Vancouver BC
Bullitt Member
Joined: December 11, 2013
Posts: 412
Likes: 0
From: Cherry Hill, NJ
I Have No Life
Joined: September 24, 2011
Posts: 10,141
Likes: 172
Ordered part of my Father's Day gifts... (Wife approved) = Scott drake and speeddawg shift *****
Part deux of Father's Day stuff is the steeda strut tower brace. Wife will "surprise" me with that. Lol!
Part deux of Father's Day stuff is the steeda strut tower brace. Wife will "surprise" me with that. Lol!
Last edited by FromZto5; May 15, 2014 at 06:49 PM.
Mach 1 Member
Joined: March 6, 2012
Posts: 866
Likes: 1
From: Quebec
Thanks Burton.
Did you have a strut tower brace before the you installed the SC?
Did you have a strut tower brace before the you installed the SC?
I Have No Life
Joined: September 24, 2011
Posts: 10,141
Likes: 172
Legacy TMS Member
Joined: August 7, 2011
Posts: 5,246
Likes: 567
From: NC
Yesterday, but I finally replaced the stock shifter in the girlfriend's GT500 with the GT500KR piece.
Quite a bit firmer engagements, a bit shorter throws, and a much more positive 2-3 engagement, as the first on-ramp after the install showed
Quite a bit firmer engagements, a bit shorter throws, and a much more positive 2-3 engagement, as the first on-ramp after the install showed