Midwest TMS'ers General Communication Thread
#4101
I suppose you're right! I didn't think of that... But it seems that you could leave them hooked up anyways, just so you don't have wires dangling all over the place, all ****-like.
#4102
Thread Starter
Legacy TMS Member
Joined: October 8, 2005
Posts: 12,397
Likes: 29
From: Medina county, OH
#4103
#4104
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
#4105
Seroiusly Tom congrats on the upgrade to Moderator. I got on a chat room several years ago about reprogramming Directv cards. I got to their top tier after several months....mmmmm remembering all 500 channels at my touch.... unlimited ****........movies......west coast 3 hours later......earth to me wake up
#4107
I got in early, 1st programmed card worked for almost 2 years then they started hitting the programs every week...then Black Sunday, they actually burned out a part of the card to make them dead. Took the programmers about 2 months to work around that one....ahhhh those were the days.
#4108
Anybody ever use a paintless dent removeal. My wife didn't like my DIY Trunk cover and we ordered another one from Granddesignmat.com
http://www.granddesignmat.com/gallery2005_2.htm
Well during the install the drill caught and push up into the bottom of the Decklid. I now have a small outee on my Decklid.
Guess I'll being going to a couple of body shops tomorrow
http://www.granddesignmat.com/gallery2005_2.htm
Well during the install the drill caught and push up into the bottom of the Decklid. I now have a small outee on my Decklid.
Guess I'll being going to a couple of body shops tomorrow
#4110
Anybody ever use a paintless dent removeal. My wife didn't like my DIY Trunk cover and we ordered another one from Granddesignmat.com
http://www.granddesignmat.com/gallery2005_2.htm
Well during the install the drill caught and push up into the bottom of the Decklid. I now have a small outee on my Decklid.
Guess I'll being going to a couple of body shops tomorrow
http://www.granddesignmat.com/gallery2005_2.htm
Well during the install the drill caught and push up into the bottom of the Decklid. I now have a small outee on my Decklid.
Guess I'll being going to a couple of body shops tomorrow
Thats why they tell you to tape the drill bit so when it does go thru, or gets caught, it wont make it to the trunk lid.
#4111
Yep It's best to follow the instructions. I got in a hurry, had very little sleep the past 2 nights and I did it wrong. All my fault but hey it can be fixed. I know I'll just throw somemore money at it
#4112
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
Anybody ever use a paintless dent removeal. My wife didn't like my DIY Trunk cover and we ordered another one from Granddesignmat.com
http://www.granddesignmat.com/gallery2005_2.htm
Well during the install the drill caught and push up into the bottom of the Decklid. I now have a small outee on my Decklid.
Guess I'll being going to a couple of body shops tomorrow
http://www.granddesignmat.com/gallery2005_2.htm
Well during the install the drill caught and push up into the bottom of the Decklid. I now have a small outee on my Decklid.
Guess I'll being going to a couple of body shops tomorrow
Hey Darrell,
I have had 2 occasions in the last few years to use Dent Wizard. Been happy with the out come in both cases. They are pretty good if the paint isn't cracked and the metal doesn't have a sharp line in the dent.
#4115
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
Hey I heard on the way to work this morning that Shania Twain is getting a divorce. I call first dibs!!
Last edited by 70MACH1OWNER; 5/16/08 at 07:52 AM.
#4116
#4119
so I have my car home in its new garage..(I backed it in so that when the garage door is open my neighbors can see it...haha)...I'll give her a bath tomorrow...It sure ran good for not being started in 6 months. And its still awesome quick.