View Poll Results: Do you prefer us lobbing Potatoes or Grenades to take care of spammers?
Lob potatoes to just stun them
1
11.11%
Lob grenades and remove them from the TMS pool permanently
8
88.89%
Voters: 9. You may not vote on this poll
Mustangs Coast to Coast
NTTAWWT
i can only imagine 6! that could get pretty rough at times. But at least you have some older daughters to help with the young ones as they grow up
Mach 1 Member
Join Date: March 21, 2010
Location: Bridgeport, Ct
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
hey all.. just stopping in .. been pretty busy.. finally got some vids up on you tube.. just a couple passes..
one of many passes
IN CAR VIEW
one of many passes
IN CAR VIEW
Post *****
Thread Starter
Awesome Rick. What was your 60'?
Well my new 90mm MAF came in for R today. It comes with a xcal 2 tuner and a tune. The tune is a conservative tune that should get me to 400 rwhp with the exhaust mods I've planned. I've been told by more than one R owner that the engine is a bullet proof as they come. Between the cast iron block, the billet rods and forged cylinders and crank, it will take anything I throw at it.
Well my new 90mm MAF came in for R today. It comes with a xcal 2 tuner and a tune. The tune is a conservative tune that should get me to 400 rwhp with the exhaust mods I've planned. I've been told by more than one R owner that the engine is a bullet proof as they come. Between the cast iron block, the billet rods and forged cylinders and crank, it will take anything I throw at it.
Join Date: December 5, 2006
Location: Trapped in Minnesota
Posts: 31,619
Likes: 0
Received 70 Likes
on
66 Posts
So jealous Gary. Two cars with 400+rwhp.
Post *****
Thread Starter
I talked to a guy today that used to own #155. He is coordinating me purchasing a carbon fiber replacement splitter for the front that weighs 6 pounds and is made from carbon fiber and carbon Kevlar. The form was made from a original R splitter which is the only POS on the car. The original splitters are also non existent anymore. So I will get this splitter on the next few months and have it painted and i will use it on the car and store the rare original so it doesn't get damaged. I'm also going to install a sacrificial aluminum strip on the underside of the splitter for scraping the driveway, etc.
This will allow me to drive the car at least.
This will allow me to drive the car at least.
NTTAWWT
I need to get an aluminum strip for the bottom of my chin spoiler when I put it on. There's all sorts of scratches on the bottom of the bumper already
Mach 1 Member
Join Date: March 21, 2010
Location: Bridgeport, Ct
Posts: 724
Likes: 0
Received 0 Likes
on
0 Posts
i got 2 runs with 1.94 60' 12.94,13.02
most runs were 2.0? one with 12.97 all passes were 107.4 108.6MPH.. engine shut down about 100' after the traps. i was in 4th by the 1/8th
1 run was 2.7 that was with "sport mode"
car spun then bogged, then every gear change bogged.. ran 13.7 @ 106
i couldnt get anymore out of the car, 618' alt of track, the CALT was 3800-4000+' with heat and humidity
i want to get it to Englishtown NJ that place is 100'ish above sea level that should be closer to 12.6' @112 ish
there are some great pics on my FB page
most runs were 2.0? one with 12.97 all passes were 107.4 108.6MPH.. engine shut down about 100' after the traps. i was in 4th by the 1/8th
1 run was 2.7 that was with "sport mode"
car spun then bogged, then every gear change bogged.. ran 13.7 @ 106
i couldnt get anymore out of the car, 618' alt of track, the CALT was 3800-4000+' with heat and humidity
i want to get it to Englishtown NJ that place is 100'ish above sea level that should be closer to 12.6' @112 ish
there are some great pics on my FB page
Post *****
Join Date: December 14, 2007
Location: State of Jefferson Mountains USA
Posts: 20,005
Likes: 0
Received 4 Likes
on
4 Posts
Ahhhhh..... The building inpector just left. Noted my progress and my permit is extended another 6 months!
So you know what that means....
.
.
.
.
.
.
.
.
.
So you know what that means....
.
.
.
.
.
.
.
.
.
IT'S DIRTY MARY TIME!! YEEEHAW!!!
Join Date: December 5, 2006
Location: Trapped in Minnesota
Posts: 31,619
Likes: 0
Received 70 Likes
on
66 Posts
Loving my tuner. I can easily break loose shifting into 2nd now.
Post *****
Thread Starter
Post *****
Join Date: December 14, 2007
Location: State of Jefferson Mountains USA
Posts: 20,005
Likes: 0
Received 4 Likes
on
4 Posts
I had a contractor build a two story "shell" Addition with Garage. So I'm finishing the interior rooms, wiring, plumbing, etc. I got the subfloor structure in place, now comes the partition wall between the garage and living area. Then maybe I can throw some insul in quickly so it will hold some heat and hopefully I can keep chipping away through the winter.
The bldg dept has been real patient with me but I always get anxious when they come out. LOL
The bldg dept has been real patient with me but I always get anxious when they come out. LOL