Resurrection of the GT..... Again
#122
Join Date: August 23, 2004
Location: Bay Area, California
Posts: 3,599
Likes: 0
Received 3 Likes
on
2 Posts
I would have thought, especially since you pulled the tranny too, that dropping it out the bottom with the K would have been easier than pulling it up.
Regardless, I'm getting pretty sick of your engine always being pulled before I can check it out.
Regardless, I'm getting pretty sick of your engine always being pulled before I can check it out.
#123
Mach 1 Member
Thread Starter
Join Date: July 4, 2007
Location: Orlando, FL
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
I'm pretty sick of pulling my own **** motor, I blame Arin's sheep.
#125
Legacy TMS Member Pr
#126
Mach 1 Member
Thread Starter
Join Date: July 4, 2007
Location: Orlando, FL
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
so I went to a club meeting over the weekend and peer pressure prevailed. Good Guys is coming up this weekend and my club always participates. The challenge was thrown down and now I have 1 week of Chaos to complete.
the car will be complete and running by friday night.
Day 1: the old engine has been broken down to a shortblock and mounted on an engine stand. I started transferring parts to the "new" shortblock. If everything goes right tomorrow, the engine should be ready to swap in tomorrow or wednesday night. Pics to follow after my BlackBerry stops being ghey
the car will be complete and running by friday night.
Day 1: the old engine has been broken down to a shortblock and mounted on an engine stand. I started transferring parts to the "new" shortblock. If everything goes right tomorrow, the engine should be ready to swap in tomorrow or wednesday night. Pics to follow after my BlackBerry stops being ghey
#127
Mach 1 Member
Thread Starter
Join Date: July 4, 2007
Location: Orlando, FL
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
Day 2: mucho progress
shortblock is now a longblock
everything staged for tomorrow morning
valve-covers, balancer, flywheel and clutch will go on 1st thing. Trans will also get stabbed in the morning and I'll do teh headers during lunch. So that puts me on track for doing it in tomorrow after work and re-wiring on thursday
shortblock is now a longblock
everything staged for tomorrow morning
valve-covers, balancer, flywheel and clutch will go on 1st thing. Trans will also get stabbed in the morning and I'll do teh headers during lunch. So that puts me on track for doing it in tomorrow after work and re-wiring on thursday
#129
Mach 1 Member
Thread Starter
Join Date: July 4, 2007
Location: Orlando, FL
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
#130
Legacy TMS Member Pr
#131
Mach 1 Member
Thread Starter
Join Date: July 4, 2007
Location: Orlando, FL
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
on the 4th day of Chaos, it awakened
I started it this evening....... with open headers and scared the service writers
small list for tomorrow: exhaust back on, cooling system, front accessories, interior and test drive.
so it's done, but because of a scheduling/family issue, no Good Guys for me
I started it this evening....... with open headers and scared the service writers
small list for tomorrow: exhaust back on, cooling system, front accessories, interior and test drive.
so it's done, but because of a scheduling/family issue, no Good Guys for me
#137
Legacy TMS Member Pr
That's good news!
Last edited by edumspeed; 3/29/10 at 12:23 AM.
#139
Mach 1 Member
Thread Starter
Join Date: July 4, 2007
Location: Orlando, FL
Posts: 500
Likes: 0
Received 0 Likes
on
0 Posts
it's been running a tune. The last tune combo was for stock bottom/cams/exhaust/intake. I'm running a nitrous version of that tune which has timing retarded through out the powerband. I need to get off my butt and get up to AED for a real tune, but work has been kinda slow