NEW! 2005-2009 Mustang Edelbrock E-Force Supercharger System!
#121
Shelby GT350 Member
Join Date: June 4, 2006
Location: McAllen, TX
Posts: 2,244
Likes: 0
Received 0 Likes
on
0 Posts
ok now someone has to sell me on this kit ALL OVER again cause after i saw the Kenne Bell "Mammoth" kit for our cars i am wondering if i should go with that or this kit.
#122
If I planned on strengthening the lower end, KB would be my choice. The Mammoth would be overkill if you want to keep stock internals.
Of course, I'm not an expert and didn't even stay at Holiday Inn Express last night!
Of course, I'm not an expert and didn't even stay at Holiday Inn Express last night!
#123
Nice SC, even with the cheese valve cover covers, any more info on the “available” 36 month/36K mile warranty? What do they mean by “available”? I assume it’s not included. Does it have to be installed by a “certified” shop, or just an added expense?
#124
Shelby GT350 Member
Join Date: June 4, 2006
Location: McAllen, TX
Posts: 2,244
Likes: 0
Received 0 Likes
on
0 Posts
i bet it has to be installed at one of their certified dealers just like FRPP and Roush parts only get the warrenty if they are installed at a qualified Ford dealership
#125
Former Vendor
Thread Starter
Join Date: January 11, 2007
Location: Aston, PA
Posts: 2,594
Likes: 0
Received 0 Likes
on
0 Posts
NEW INFORMATION ON THE EDELBROCK E-FORCE SUPERCHARGER KITS:
http://www.tillmanspeed.com/Edelbrock_EForce.pdf
EDELBROCK WILL BE OFFERING THE FOLLOWING ADDITIONAL REPLACEMENT PARTS AND UPGRADE KITS TO THE SUPERCHARGER, AS WELL AS A TUNER SUPERCHARGER KIT (COMPETITION KIT) THAT WILL ALLOW YOU TO PICK DIFFERENT COMPONENTS!
Cooling System Upgrade Kit
--------------------------------------------------------------------
WE ARE OFFERING STAGED E-FORCE PACKAGES AS OF NOW, DETAILS COMING IN OUR NEXT POST BELOW!!!!!
http://www.tillmanspeed.com/Edelbrock_EForce.pdf
EDELBROCK WILL BE OFFERING THE FOLLOWING ADDITIONAL REPLACEMENT PARTS AND UPGRADE KITS TO THE SUPERCHARGER, AS WELL AS A TUNER SUPERCHARGER KIT (COMPETITION KIT) THAT WILL ALLOW YOU TO PICK DIFFERENT COMPONENTS!
COOLING SYSTEM UPGRADE KIT
FOR 2005-06 FORD MUSTANGS
Our Cooling System Upgrade Kit is necessary when installing the new Edelbrock E-Force Supercharger Kits #1580 and #1585 in a 2005-06 Mustang GT. This kit relocates the thermostat from the cold side of the radiator to the hot side for improved cooling. Kit contains all necessary hoses, clamps and hardware.
FOR 2005-06 FORD MUSTANGS
Our Cooling System Upgrade Kit is necessary when installing the new Edelbrock E-Force Supercharger Kits #1580 and #1585 in a 2005-06 Mustang GT. This kit relocates the thermostat from the cold side of the radiator to the hot side for improved cooling. Kit contains all necessary hoses, clamps and hardware.
Cooling System Upgrade Kit
(for 2005-06 Ford Mustang GT).................................................. ..#15804
--------------------------------------------------------------------
HARDWARE KIT
FOR 2009 FORD MUSTANG
This kit is required when installing the new Edelbrock E-Force Supercharger Kits #1580 and #1585 in a 2009 Ford Mustang GT. Includes new intake gaskets and all the necessary hardware for 2009 specific installation.
Hardware Kit for 2009 Ford Mustang GT .................................................. ............#15805
FOR 2009 FORD MUSTANG
This kit is required when installing the new Edelbrock E-Force Supercharger Kits #1580 and #1585 in a 2009 Ford Mustang GT. Includes new intake gaskets and all the necessary hardware for 2009 specific installation.
Hardware Kit for 2009 Ford Mustang GT .................................................. ............#15805
--------------------------------------------------------------------
BELT TENSIONER BRACE
This new belt tensioner brace is intended for use on 2005-09 Mustangs and F-150 trucks with an
aftermarket supercharger installed. The stock belt tensioner is cast aluminum and has been known to bend and even break under extreme driving. The Edelbrock Steel Belt Tensioner Brace is an inexpensive solution to this common problem. It simply bolts on to your stock tensioner and prevents any deflection of the cast arm. Already included with E-Force supercharger kit #1580 (street) and #1585 (competition).
Steel Belt Tensioner Brace .................................................. ...............................#15806
This new belt tensioner brace is intended for use on 2005-09 Mustangs and F-150 trucks with an
aftermarket supercharger installed. The stock belt tensioner is cast aluminum and has been known to bend and even break under extreme driving. The Edelbrock Steel Belt Tensioner Brace is an inexpensive solution to this common problem. It simply bolts on to your stock tensioner and prevents any deflection of the cast arm. Already included with E-Force supercharger kit #1580 (street) and #1585 (competition).
Steel Belt Tensioner Brace .................................................. ...............................#15806
--------------------------------------------------------------------
FUEL INJECTORS
Fuel Injectors
Fuel Injectors
(41 lb/hr, EV14, USCAR, 60mm Body, Set of 8).................................................. ....#15807
--------------------------------------------------------------------
COMPETITION COMPONENTS
E-FORCE COMPETITION SUPERCHARGER KIT
The Edelbrock E-Force competition supercharger is based off of our street supercharger kit #1580, but is paired down to the essential components that a racer needs, without the extras that experienced racers prefer to customize for their own competitive advantage. This kit contains: supercharger manifold assembly featuring, 85mm electronic throttle body, cast aluminum alternator/idler bracket, steel belt tensioner brace, cast aluminum water crossover, dual core low temperature heat exchanger for intercooler system, electric intercooler water pump, intercooler recovery tank, -12 AN intercooler fittings, steel idler pulleys with heavy duty high speed bearings and all the necessary mounting hardware, wiring and plumbing. For competition racing use only.
E-Force Competition Supercharger Kit
The Edelbrock E-Force competition supercharger is based off of our street supercharger kit #1580, but is paired down to the essential components that a racer needs, without the extras that experienced racers prefer to customize for their own competitive advantage. This kit contains: supercharger manifold assembly featuring, 85mm electronic throttle body, cast aluminum alternator/idler bracket, steel belt tensioner brace, cast aluminum water crossover, dual core low temperature heat exchanger for intercooler system, electric intercooler water pump, intercooler recovery tank, -12 AN intercooler fittings, steel idler pulleys with heavy duty high speed bearings and all the necessary mounting hardware, wiring and plumbing. For competition racing use only.
E-Force Competition Supercharger Kit
(for 2005-09 Ford Mustang 4.6L 3V) ............................#1585*
--------------------------------------------------------------------
E-FORCE COMPETITION AIR INTAKE SYSTEM
The E-Force Competition Air Intake System includes a high flow, 95mm, Mass Airflow Sensor (MAFS) capable of supporting up to 90 lbs/min of air flow. It includes an 8" long, reusable, open element filter with plastic shroud. This system is for use with Competition sSpercharger kit #1585.
E-Force Competition Air Intake System .................................................. ..............................#15808
The E-Force Competition Air Intake System includes a high flow, 95mm, Mass Airflow Sensor (MAFS) capable of supporting up to 90 lbs/min of air flow. It includes an 8" long, reusable, open element filter with plastic shroud. This system is for use with Competition sSpercharger kit #1585.
E-Force Competition Air Intake System .................................................. ..............................#15808
--------------------------------------------------------------------
PULLEYS FOR E-FORCE
COMPETITION SUPERCHARGER KITS
E-Force Competition Supercharger Pulleys are required for installation of E-Force Supercharger kit #1585. Available in four different sizes for fine tuning air flow needs for your specific racing needs.
3.50" Pulley............................................ .................................................. .......#15820
3.25" Pulley............................................ .................................................. .......#15821
3.00" Pulley............................................ .................................................. .......#15822
2.75" Pulley............................................ .................................................. .......#15823
COMPETITION SUPERCHARGER KITS
E-Force Competition Supercharger Pulleys are required for installation of E-Force Supercharger kit #1585. Available in four different sizes for fine tuning air flow needs for your specific racing needs.
3.50" Pulley............................................ .................................................. .......#15820
3.25" Pulley............................................ .................................................. .......#15821
3.00" Pulley............................................ .................................................. .......#15822
2.75" Pulley............................................ .................................................. .......#15823
WE ARE OFFERING STAGED E-FORCE PACKAGES AS OF NOW, DETAILS COMING IN OUR NEXT POST BELOW!!!!!
Last edited by TillmanSpeed; 12/23/08 at 11:07 AM.
#126
Mach 1 Member
Join Date: January 30, 2008
Location: Pacific NW USA
Posts: 721
Likes: 0
Received 2 Likes
on
2 Posts
I really like that intake and intercooler design!
Any absolute word yet on whether it fits under the factory Bullitt Strut Tower Brace?
Gotta be able to keep the Bullitt factory "serialized" strut tower brace.
Gotta be able to keep the Bullitt factory "serialized" strut tower brace.
#127
Cobra Member
Join Date: October 15, 2008
Location: Brew City
Posts: 1,373
Likes: 0
Received 0 Likes
on
0 Posts
Chris, does this mean we are getting closer to these shipping??? I am getting anxious and can't wait to see that part in my garage... and then ultimately on my car!
#128
Cobra Member
Join Date: August 5, 2008
Location: Arvada, CO
Posts: 1,369
Likes: 0
Received 0 Likes
on
0 Posts
#131
Former Vendor
Thread Starter
Join Date: January 11, 2007
Location: Aston, PA
Posts: 2,594
Likes: 0
Received 0 Likes
on
0 Posts
Lysholm (Swedish) makes twin screw blowers. They also manufacture the new Vortech twin screw as well. This Eaton TVS four lobe roots style blower is made in America.
Chris Rose
Tillman Speed Inc.
www.TillmanSpeed.com
610-497-5776
Chris Rose
Tillman Speed Inc.
www.TillmanSpeed.com
610-497-5776
#134
Cobra Member
Join Date: October 15, 2008
Location: Brew City
Posts: 1,373
Likes: 0
Received 0 Likes
on
0 Posts
I've got one coming and will be installing myself, just patiently awaiting a delivery date from Tillman. As of last week, CR was speculating they may start shipping this week as Edelbrock was shut down over the holidays.
Chris, any update??
Chris, any update??
#135
I ordered mine from a Edelbrock ' National Sales Manager '. He told me today that there still targeting a FEB 1 date.
Thats all I know for now. I do know that I have to remove my Saleen UDP's. Any one want a killer deal on a set of less than one year old saleen UDP's?
Tim
Thats all I know for now. I do know that I have to remove my Saleen UDP's. Any one want a killer deal on a set of less than one year old saleen UDP's?
Tim
Last edited by mustangbaxter; 1/4/09 at 09:14 AM.