Ponies on The Run (Again)
Legacy TMS Member
Remove all visible screws....... then remove the snap-in panels behind the door handle and arm rest and remove those bolts. Once you have all screws and bolts out, remove the panel by lifting it up and towards you.
Different subject- here's the link to my AVIC D3 pix.
http://forums.bradbarnett.net/showthread.php?t=72846
Different subject- here's the link to my AVIC D3 pix.
http://forums.bradbarnett.net/showthread.php?t=72846
My only chance at everyone seeing my chrome MGW Seat Lever Buckles!
Pretty nice, huh?
Attachment 34745
Pretty nice, huh?
Attachment 34745
btw I like the poney tail pic in the side mirror as opposed to the straight hair in the chair ? chop
Cobra R Member
Join Date: May 8, 2006
Location: Florida
Posts: 1,967
Likes: 0
Received 0 Likes
on
0 Posts
I think I have them all out now. Is there just 1 screw behind the power switch plate/arm rest? I got the power switch plate out, but the arm rest didn't come out with it. I pulled on the door and it feels like there might still be a screw somewhere. I didn't pull real hard because it was dark and I couldn't see anything. They'll be done tomorrow and hopefully my couple lowering problems will be taken care of.
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
That pretty much sums it up. Just take your time and be careful. I took the door cable off as well if I remember so I could place the door panel completely out of my way. When putting it back on be careful and don't over tighten the screws. that plastic is weak and can crumple under to much torque.
Legacy TMS Member
Join Date: May 24, 2006
Location: San Diego
Posts: 7,409
Likes: 0
Received 0 Likes
on
0 Posts
SHR Fuel door gone....
Decided not to keep the fuel door so it's on it's way back to SHR. But....I've decided to get a custom rear medallion like Brads. Only thing I may do differently is slap on a GT emblem. Here's a pic for those of you that have no idea what I'm talking about.
Legacy TMS Member
Join Date: May 24, 2006
Location: San Diego
Posts: 7,409
Likes: 0
Received 0 Likes
on
0 Posts
Cobra Member
Join Date: May 17, 2007
Location: Texa$
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
This is how all Mustangs should come from the factory as.....
Tasca Super Boss 429 Member
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
Do you use one of these? If so how do you like it?
Bill
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
Queen Mary, Stang & a Wedding
Just washed the Roush at 6:30 a.m.! Getting ready for the Queen Mary event. Of course I'll document the stangs there! Nup's will be later I think TacoBill, Charlie and I are doing to do the convoy there...CONVOY! Remenber that tune, oh sorry I dated myself! Might try to catch breakfast at Ricky & Ronnie Stay tuned for Wedding at the Queen Mary!
Jed
Jed
Team Mustang Source
I did mine Thursday. I'm leaving here around 9:30 or so. It's the first time I've washed my car since the Queen Mary XI !!!! and I think the longest I've let it go.
Best part of today... Checking out Jed's car ! Who cares about the wedding. I want to see that blower
Best part of today... Checking out Jed's car ! Who cares about the wedding. I want to see that blower
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
Jed
Cobra R Member
Join Date: May 8, 2006
Location: Florida
Posts: 1,967
Likes: 0
Received 0 Likes
on
0 Posts
The SHR louvers are the only ones I've ever liked. Too bad you can't see them in person, because I know you would like them. They really are high quality stuff. (of course)
Legacy TMS Member
Nice choice Leo, I like those a lot. Maybe I'll invest sometime in the future. Who will do the install?
Legacy TMS Member
Hey guys, we had the Brenspeed fall dyno day today... I pulled a new best when running my stock 17" wheels- 469/414. I posted some vids of the pull........ BUT, also there were many other cars there, one of which was an 1130 rwhp Monte Carlo! Check out the vids!
http://forums.bradbarnett.net/showth...11#post1033111
http://forums.bradbarnett.net/showth...11#post1033111
Cobra Member
Join Date: May 17, 2007
Location: Texa$
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys, we had the Brenspeed fall dyno day today... I pulled a new best when running my stock 17" wheels- 469/414. I posted some vids of the pull........ BUT, also there were many other cars there, one of which was an 1130 rwhp Monte Carlo! Check out the vids!
http://forums.bradbarnett.net/showth...11#post1033111
http://forums.bradbarnett.net/showth...11#post1033111