Convertible Owners, C'mon In Here.....
9/25/07, 06:31 AM
#101
Member
Join Date: May 23, 2007
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
I think there has been a couple of TSB's about the top but this one is new to me. I would still go after them.
Just remember sometimes these things go bad and instead of a wrinkle the new top might leak/not fit well and there will be a big scratch on your decklid.
Proceed with caution.
Just remember sometimes these things go bad and instead of a wrinkle the new top might leak/not fit well and there will be a big scratch on your decklid.
Proceed with caution.
12/7/07, 01:10 AM
#104
Bullitt Member
Thread Starter
Join Date: July 22, 2005
Posts: 209
Likes: 0
Received 0 Likes
on
0 Posts
12/7/07, 07:21 AM
#105
Legacy TMS Member
You'll love the one touch top button. I hit mine and then by the time I've taken down the windshield sun screen and put on my seat belt I'm ready to go.
B
B
Semper Fi
B
BSemper Fi
12/7/07, 09:21 AM
#106
Cobra Member
You'll love the one touch top button. I hit mine and then by the time I've taken down the windshield sun screen and put on my seat belt I'm ready to go.
12/9/07, 05:42 AM
#108
Bullitt Member
Join Date: January 8, 2007
Posts: 408
Likes: 0
Received 0 Likes
on
0 Posts
I had the top replaced on my 07 GT about a month ago and the driver's side rear just behind the rear window has a definite wrinkle. The work was farmed out from the ford dealer to a local upholsterer and I talked to him after I got it back and he told me the wrinkle would clear up on its own in about a month. Well it has been about a month and I am not noticing a big improvement. He did tell me that if it didn't clear up that I should bring it in to him and he would make it right. Has anyone had any experience with a sitaution like this and was it able to be corrected.
Ron
Ron
1/22/08, 03:37 PM
#110
Mach 1 Member
Join Date: July 28, 2006
Posts: 970
Likes: 0
Received 0 Likes
on
0 Posts
I ordered and received my one-touch top module. I hope to install tomorrow once this 34 and rain weather pattern leaves NC. FWIW, Valerie was the name on the order, wife's name FTW.
1/22/08, 04:37 PM
#111
Bullitt Member
Join Date: November 9, 2007
Location: South Carolina
Posts: 241
Likes: 0
Received 0 Likes
on
0 Posts
I have this upgrade. My first module was bad -- wouldn't raise -- service from WebElectric was super. He spent 45 minutes on the phone troubleshooting -- send me a new one and a pre-paid mailer to send back the old one for a QC determination. All are tested. I also installed sequentials. If you have Shaker 1000 -- the plug and play sequentials are more difficult -- cause you have to remove the subs or have very small hands.
The top module was pretty straightforward -- but you need a lot of light and care -- the wire harness is a bit close on some of the colors.
This is a top notch fun upgrade that works great.
The top module was pretty straightforward -- but you need a lot of light and care -- the wire harness is a bit close on some of the colors.
This is a top notch fun upgrade that works great.
1/23/08, 03:04 PM
#112
Mach 1 Member
Join Date: July 28, 2006
Posts: 970
Likes: 0
Received 0 Likes
on
0 Posts
Has anyone done this with the traction control modification? The One-touch module cuts the red/black wire and the T/C modification needs that wire to connect to. What happens to the power to/from radio, since the wire is cut? Any thoughts?
1/23/08, 04:16 PM
#113
Bullitt Member
Join Date: May 17, 2005
Posts: 370
Likes: 0
Received 0 Likes
on
0 Posts
Nevermind, I found it.
1/24/08, 03:51 PM
#116
Mach 1 Member
Join Date: July 28, 2006
Posts: 970
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post