View Poll Results: Do you prefer us lobbing Potatoes or Grenades to take care of spammers?
Lob potatoes to just stun them
2
16.67%
Lob grenades and remove them from the TMS pool permanently
10
83.33%
Voters: 12. You may not vote on this poll
Mustangs Coast to Coast
#521
Post *****
Thread Starter
Looks good Nathan. My spoiler doesn't rattle anymore because its a Cervinis and is fastened and stuck on all around the perimter. But my taillights rattle really bad. That and probably every piece of interior trim.
#522
Post *****
Thread Starter
Golf cart update.
I have the cowl and body prepped with Bulldog adhesion promoter. And I've got a quart of real automotive paint and some kind of mix that goes in with it to spray the cowl and body with. Not sure about clearcoat or not, we'll see how I do with the spraygun on the body. I have resprayed the frame with satin black and to be honest it looks really good. I do need to hit a few more spots on the bottom side and I'm going to go ahead and pull the rack and pinion steering and motor/differential and vlean them up. As of now its a full off restoration. My parts have shipped. But I don't have an expected arrival date yet. I also need to find the matte black 3M stripe vinyl for the stripes to match the car. I found a link to some amazing golf cart paint jobs. Check these out. I'm tempted to get the orange flame on black but I've spent enough already.
http://www.deckersgarage.com/cartbodygalleryfire.htm
I have the cowl and body prepped with Bulldog adhesion promoter. And I've got a quart of real automotive paint and some kind of mix that goes in with it to spray the cowl and body with. Not sure about clearcoat or not, we'll see how I do with the spraygun on the body. I have resprayed the frame with satin black and to be honest it looks really good. I do need to hit a few more spots on the bottom side and I'm going to go ahead and pull the rack and pinion steering and motor/differential and vlean them up. As of now its a full off restoration. My parts have shipped. But I don't have an expected arrival date yet. I also need to find the matte black 3M stripe vinyl for the stripes to match the car. I found a link to some amazing golf cart paint jobs. Check these out. I'm tempted to get the orange flame on black but I've spent enough already.
http://www.deckersgarage.com/cartbodygalleryfire.htm
#523
We have a roll of matt Black vinal n=but it's a way up this way grrr to bad you couldn't use that Rhino Bed stuff to coat the floors , I seen it on Mythbuster and it with stood a lot of C-$ explosives Tough stough. I'm not a golfer btw only mini golf hole in one most often.
#524
Join Date: December 5, 2006
Location: Trapped in Minnesota
Posts: 31,620
Likes: 0
Received 70 Likes
on
66 Posts
It's on there really tight, but the stupid brake light, is what's causing most of it. And I can't tighten it without taking off the whole dang thing. It's a big pain in the butt. If I were to paint my car all over again, I think I'd just skip the spoiler. It's been nothing but a problem.
#525
Legacy TMS Member Pr
Hi there MCTC crew.
Last edited by edumspeed; 7/22/08 at 04:07 PM.
#526
It's on there really tight, but the stupid brake light, is what's causing most of it. And I can't tighten it without taking off the whole dang thing. It's a big pain in the butt. If I were to paint my car all over again, I think I'd just skip the spoiler. It's been nothing but a problem.
#527
Join Date: December 5, 2006
Location: Trapped in Minnesota
Posts: 31,620
Likes: 0
Received 70 Likes
on
66 Posts
^Sorta close to what I did. I took the spoiler completely off, and put some strips of dynamat onto the top of the brake light where it touches the spoiler, and then put it back on really tight. Now there's almost no rattle at all. Something in the trunk doesn't sound right though. I guess I have to look into that now. Hopefully tomorrow I can get the doors done!
#530
Join Date: December 5, 2006
Location: Trapped in Minnesota
Posts: 31,620
Likes: 0
Received 70 Likes
on
66 Posts
I need more money....
http://www.crutchfield.com/S-AjjhIXk...M450&s=0&cc=01
or
http://www.crutchfield.com/App/Produ...MRPM500&tp=115
http://www.crutchfield.com/S-AjjhIXk...912U&s=0&cc=01
http://www.crutchfield.com/S-AjjhIXk...050W&s=0&cc=01
http://www.crutchfield.com/S-AjjhIXk...10D6&s=0&cc=01
http://www.crutchfield.com/S-AjjhIXk...M450&s=0&cc=01
or
http://www.crutchfield.com/App/Produ...MRPM500&tp=115
http://www.crutchfield.com/S-AjjhIXk...912U&s=0&cc=01
http://www.crutchfield.com/S-AjjhIXk...050W&s=0&cc=01
http://www.crutchfield.com/S-AjjhIXk...10D6&s=0&cc=01
Last edited by Blue Notch; 7/22/08 at 11:20 PM.
#531
^Sorta close to what I did. I took the spoiler completely off, and put some strips of dynamat onto the top of the brake light where it touches the spoiler, and then put it back on really tight. Now there's almost no rattle at all. Something in the trunk doesn't sound right though. I guess I have to look into that now. Hopefully tomorrow I can get the doors done!