Lots of new parts to install.
10/19/12, 11:29 PM
#21
V6 Member
Thread Starter
Join Date: November 8, 2010
Location: Austin TX
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
10/22/12, 08:48 AM
#26
V6 Member
Thread Starter
Join Date: November 8, 2010
Location: Austin TX
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
10/22/12, 10:05 AM
#27
Bullitt Member
Join Date: July 18, 2011
Location: Austin, Texas
Posts: 207
Likes: 0
Received 0 Likes
on
0 Posts
It's a long story... pretty stupid on my part. I traded for the Stang, and then I decided I wanted my old car back... and now I miss the Stang and all the power. I'm going to get another in next year. 
I'd love to take a look at your car one day. Looks like it's going to be BA!
I'd love to take a look at your car one day. Looks like it's going to be BA!
10/24/12, 01:46 PM
#29
Bullitt Member
Join Date: March 19, 2012
Location: Louisville, KY
Posts: 456
Likes: 0
Received 0 Likes
on
0 Posts
In his sig (which you may or may not be able to see) it says he is doing the JPC NA 500 rwhp package, with that said I'm betting its JPC LT's
Let me know how that top dog package works out for you! That's pretty exciting
Let me know how that top dog package works out for you! That's pretty exciting
10/25/12, 09:17 PM
#30
V6 Member
Thread Starter
Join Date: November 8, 2010
Location: Austin TX
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
I went with the JBA long tubes.
I pieced together the kit, opted with the JBA long tubes.
The motor is in, trans bolted up, all new exhaust in. I need to trim the coupler for my CAI (airaid) to fit the boss manifold.
But I have come across a problem, the clutch system is not pressurized at all (clutch pedal snaps to the floor). I noticed the brake/clutch fluid reservoir is a bit low. So I'm going to check the clutch line for leaks, bleed the system and hopefully that fixes it.
After that, it will be ready for start up and break-in.
The motor is in, trans bolted up, all new exhaust in. I need to trim the coupler for my CAI (airaid) to fit the boss manifold.
But I have come across a problem, the clutch system is not pressurized at all (clutch pedal snaps to the floor). I noticed the brake/clutch fluid reservoir is a bit low. So I'm going to check the clutch line for leaks, bleed the system and hopefully that fixes it.
After that, it will be ready for start up and break-in.
12/14/12, 09:46 AM
#32
V6 Member
Thread Starter
Join Date: November 8, 2010
Location: Austin TX
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
Sorry for the lack of updates recently, been busy with the holiday season. The moose is up and running like a champ.
The issue with the clutch pedal was a stupid one. I never brought the vehicle down off of stands after finishing the exhaust install, and because of the slope of my driveway, the bubbles in the clutch system weren't able to escape. After leveling the car, it only took a short period of time to fix that.
Next thing I need is tires. Rear end is not controllable until 3rd gear, and on some roads, its even sketchy there. I'm working on getting some dyno time in, hopefully next week. The shop had to replace some electronics last week, so it should be good to go. Hoping I hit that 500rwhp mark.
The issue with the clutch pedal was a stupid one. I never brought the vehicle down off of stands after finishing the exhaust install, and because of the slope of my driveway, the bubbles in the clutch system weren't able to escape. After leveling the car, it only took a short period of time to fix that.
Next thing I need is tires. Rear end is not controllable until 3rd gear, and on some roads, its even sketchy there. I'm working on getting some dyno time in, hopefully next week. The shop had to replace some electronics last week, so it should be good to go. Hoping I hit that 500rwhp mark.
Thread
Thread Starter
Forum
Replies
Last Post
tj@steeda
2015 - 2023 MUSTANG
0
7/30/15 06:47 AM