Ponies on The Run (Again)
#941
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Well I am at work today so no start on the install yet.
Bill in the instructions it says you only have to place a strip of masking tape at the beginning and end of the areas and align the stripes to them, BUT I think I will mask the center line the entire length of the car. I think this will allow for a much more accurate layout.
No centerline marked or even measured yet.
Why would I mark the centerline of the masking tape ?
If the masking tape is centered, I don't see a need for marking the center of it. (Explain please ) Unless you mean BEFORE I place it on the car.
I will use 3M Green Automotive Masking Tape, same as in the pics of the scoop install (Only way to go IMO)
Later this afternoon or evening, if I get a Chance, I will lay the hood stripes on the car and mask the ends down, snap a couple shots and post them for you Bill, but keep in mind the following:
1 - They will have the backing tape on so they will be about ¼" to ½" Wider than 12"
2 - They will not be perfectly centered
3 - Edges will appear rough
4 - They will probably have a little "curl" to them as well.
I'm not nervous, just anxious.
Bill in the instructions it says you only have to place a strip of masking tape at the beginning and end of the areas and align the stripes to them, BUT I think I will mask the center line the entire length of the car. I think this will allow for a much more accurate layout.
No centerline marked or even measured yet.
Why would I mark the centerline of the masking tape ?
If the masking tape is centered, I don't see a need for marking the center of it. (Explain please ) Unless you mean BEFORE I place it on the car.
I will use 3M Green Automotive Masking Tape, same as in the pics of the scoop install (Only way to go IMO)
Later this afternoon or evening, if I get a Chance, I will lay the hood stripes on the car and mask the ends down, snap a couple shots and post them for you Bill, but keep in mind the following:
1 - They will have the backing tape on so they will be about ¼" to ½" Wider than 12"
2 - They will not be perfectly centered
3 - Edges will appear rough
4 - They will probably have a little "curl" to them as well.
I'm not nervous, just anxious.
#942
Originally Posted by OKCMustangGT
Bill in the instructions it says you only have to place a strip of masking tape at the beginning and end of the areas and align the stripes to them, BUT I think I will mask the center line the entire length of the car. I think this will allow for a much more accurate layout.
Originally Posted by OKCMustangGT
Why would I mark the centerline of the masking tape ?
Originally Posted by OKCMustangGT
If the masking tape is centered, I don't see a need for marking the center of it. (Explain please ) Unless you mean BEFORE I place it on the car.
Originally Posted by OKCMustangGT
I will use 3M Green Automotive Masking Tape, same as in the pics of the scoop install (Only way to go IMO)
Originally Posted by OKCMustangGT
Later this afternoon or evening, if I get a Chance, I will lay the hood stripes on the car and mask the ends down, snap a couple shots and post them for you...
#943
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TacoBill
Never seen Green 3M masking tape before... Where you get this from? Home Depot?
3M Scotch® Performance Masking Tape
Attachment 1459
#944
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Reply from Rob at BSM when I sent pictures of the stripe and the sheets I received. (supposed to be two sheets, I received three)
"Yeah i remember now, the machine moved mid-cut and messed up the solid driver side bumper piece (and apparently the passenger hood stripe) as well as one of the cutout bumper pieces."
Rob already has the piece cut and on it's way. Great guy and FAST e-mail responses.
"Yeah i remember now, the machine moved mid-cut and messed up the solid driver side bumper piece (and apparently the passenger hood stripe) as well as one of the cutout bumper pieces."
Rob already has the piece cut and on it's way. Great guy and FAST e-mail responses.
#945
Originally Posted by OKCMustangGT
Looks like it sticks pretty good. I'm assuming it has a stronger adhesion compared to the blue painters tape?
I may have to look around for a 1 1/2" roll.
#946
Originally Posted by OKCMustangGT
Reply from Rob at BSM when I sent pictures of the stripe and the sheets I received. (supposed to be two sheets, I received three)
I also e-mailed Rob this morning asking about the nozzle and rear emblem cut-outs (as to if there's a gap around them). Still waiting for a response as of 0938hrs PST.
#947
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TacoBill
3 sheets? You lost me again.
Since the machine messed up they had to get a third sheet and recut two of the pieces. That is why I have three sheets or should I say rolls?
Clear yet ?
Originally Posted by TacoBill
Looks like it sticks pretty good. I'm assuming it has a stronger adhesion compared to the blue painters tape?
Originally Posted by TacoBill
I may have to look around for a 1 1/2" roll.
#948
Originally Posted by OKCMustangGT
... That is why I have three sheets or should I say rolls?
Clear yet ?
Clear yet ?
Another thing I've been thinking about, although most likely totally unneccessary, is to use distilled water for the solution.
Think it'll help or am I whacked?
Still no respose from Rob. Maybe current customers get a quicker response (?). It's not a 911 question anyway, I'd like to see your final before I place my order.
#949
Daryl- Does marking the center of the green tape make any sense (like my attached pic a few posts up)? Or, do you have an alternate way of locating the tape center?
#950
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TacoBill
Daryl- Does marking the center of the green tape make any sense (like my attached pic a few posts up)? Or, do you have an alternate way of locating the tape center?
I am sure that is the method I will use, but here is another question.
Since I can't install the Passenger Side Hood Stripe (the defective one) should I go ahead and install the driver side one? I am thinking yes, even though it will look odd as hell until I get the replacement stripe.
Should I start on the roof first or still do the hood first ?
My luck with the stuff is uncanny isn't it ?
I don't think distilled water would be necessary, but I don't think it would hurt either.
Am I using distilled water? No
#951
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Response from Bob @ Mustang Tuning concerning the special pricing on the CDC Shaker System.
"We got those at a special deal and that’s why we were able to offer them at that price. Your best bet would be to contact one of our customer service representatives and see if they can give you a similar discount."
Looks like I will be making a phone call.
Tom are you serious about purchasing the Shaker? If so maybe we can work out a special price if we both buy at the same time.
"We got those at a special deal and that’s why we were able to offer them at that price. Your best bet would be to contact one of our customer service representatives and see if they can give you a similar discount."
Looks like I will be making a phone call.
Tom are you serious about purchasing the Shaker? If so maybe we can work out a special price if we both buy at the same time.
#952
Originally Posted by OKCMustangGT
Yea it makes perfect sense now. At first I was like WTF ? LOL
I am sure that is the method I will use, but here is another question.
Since I can't install the Passenger Side Hood Stripe (the defective one) should I go ahead and install the driver side one? I am thinking yes, even though it will look odd as hell until I get the replacement stripe.
Should I start on the roof first or still do the hood first ?
My luck with the stuff is uncanny isn't it ?
I don't think distilled water would be necessary, but I don't think it would hurt either.
Am I using distilled water? No
I am sure that is the method I will use, but here is another question.
Since I can't install the Passenger Side Hood Stripe (the defective one) should I go ahead and install the driver side one? I am thinking yes, even though it will look odd as hell until I get the replacement stripe.
Should I start on the roof first or still do the hood first ?
My luck with the stuff is uncanny isn't it ?
I don't think distilled water would be necessary, but I don't think it would hurt either.
Am I using distilled water? No
Save the hood for last, that way you'll only have to mask it once. Plus it's 'supposed' to be the easiest, especially after you've experienced the rest of the car.
Of course if you go buy a gallon of distilled and use it, you'll never tell us anyway!!
#953
Originally Posted by OKCMustangGT
Tom are you serious about purchasing the Shaker? If so maybe we can work out a special price if we both buy at the same time.
Tom, Tom, Tom, Tom....
#954
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TacoBill
Of course if you go buy a gallon of distilled and use it, you'll never tell us anyway!!
Tom is MIA today
#955
Originally Posted by OKCMustangGT
Now what brought that comment on
Tom is MIA today
Tom is MIA today
Tom has alot of reading to do... with a whopping question at the end.
#956
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by TacoBill
Well I was thinking that if you did change your mind at the last minute and switched from tap to distilled (mostly for good luck), you'd be too ashamed to tell us... or would you.
#958
Originally Posted by OKCMustangGT
Nah, I would tell you, I would just add something like D A M N you Bill
Hot off the press tips on vinyl graphic installations!
Tip 1
Tip 2
Gonna buy some D-Water now?
#960
Shelby GT350 Member
Thread Starter
Join Date: January 17, 2006
Location: Tornado Alley
Posts: 2,061
Likes: 0
Received 0 Likes
on
0 Posts
Just for you Bill. Good thing these aren't for real, cause my eyeballing sucked.
Attachment 1462Attachment 1463Attachment 1464Attachment 1465Attachment 1466
My opionion, as biased as it is, says these are gonna ROCK
Attachment 1462Attachment 1463Attachment 1464Attachment 1465Attachment 1466
My opionion, as biased as it is, says these are gonna ROCK