Notices
2010-2014 Mustang Information on The S197 {GenII}
Sponsored By:
Sponsored By:

'10-'13 Front Stone/Splash Guards

Thread Tools
 
Search this Thread
 
Old 6/15/12, 05:29 PM
  #21  
Team Mustang Source
 
montreal ponies's Avatar
 
Join Date: January 30, 2004
Location: Montreal
Posts: 3,738
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by us002840
I HAVE the clear bra installed, if you look closely. Problem is, tires are so wide and throw lots of debry, that the clear bra was being damaged in just two weeks. No more damage after install of mud flaps.
Yeah i know, you have a point. Would you have a more general pic say looking at the entire car from the back. Just want to see what they look like standing from the side. thx
Old 6/15/12, 07:18 PM
  #22  
V6 Member
 
us002840's Avatar
 
Join Date: January 6, 2012
Location: NE Ohio
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by FromZto5
I can't see pics well on phone but can you please address my question #2 from above? Are they flat sheets or naturally curved and molded as such?

Thx
Originally Posted by montreal ponies
Yeah i know, you have a point. Would you have a more general pic say looking at the entire car from the back. Just want to see what they look like standing from the side. thx
Sure, I will take a few shots from the rear so that you can see the actual "footprint" of the flaps. They are VERY close in dimension to the factory flaps. And, the go on and off in less than two minutes. Simple pushpin removal/install. I LIKE them.
Old 6/15/12, 08:25 PM
  #23  
GT Member
 
outtaphase's Avatar
 
Join Date: April 17, 2012
Location: Connecticut
Posts: 115
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by us002840
And, the go on and off in less than two minutes. Simple pushpin removal/install. I LIKE them.
Very stupid (or just simple) question from someone who ordered these and plans to put them on my '13 when it gets here -

What technique do you use to remove the push pins? How did you pry them out from the outside? I see them same pins on my '10 but I figured I'd ask first instead of playing with them.

Last edited by outtaphase; 6/15/12 at 08:29 PM.
Old 6/15/12, 11:54 PM
  #24  
V6 Member
 
us002840's Avatar
 
Join Date: January 6, 2012
Location: NE Ohio
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by outtaphase
Very stupid (or just simple) question from someone who ordered these and plans to put them on my '13 when it gets here -

What technique do you use to remove the push pins? How did you pry them out from the outside? I see them same pins on my '10 but I figured I'd ask first instead of playing with them.
I used a small screwdriver, flat, to start the pin removal, and then just pulled the entire "shaft" out with my hand. Simple and yet very strong and secure. Place the "shaft" back into the original hole and push the pin in by hand. EASY!
Old 6/19/12, 04:12 PM
  #25  
Shelby GT500 Member
 
MyStang2010GB's Avatar
 
Join Date: September 8, 2009
Location: Lithia, FL
Posts: 2,586
Received 4 Likes on 4 Posts
These look great and could not be any simpler to install !! the ONLY complaint I have is the wheel well side is a smooth gloss black. the other side is a nice pebbled finish like the rear ones. they look great!!

Name:  2012-06-19_17-17-56_334.jpg
Views: 317
Size:  59.6 KB
Name:  2012-06-19_17-18-07_260.jpg
Views: 334
Size:  44.4 KB
Old 6/20/12, 09:57 PM
  #26  
GT Member
 
MikeD73USA's Avatar
 
Join Date: April 29, 2012
Posts: 152
Likes: 0
Received 0 Likes on 0 Posts
How much for the set?
Old 6/20/12, 10:04 PM
  #27  
GT Member
 
Barry626's Avatar
 
Join Date: March 31, 2012
Location: Rochester, NY
Posts: 140
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by MikeD73USA
How much for the set?
Apprx $58.00 with shipping.
Old 6/21/12, 12:41 AM
  #28  
Cobra R Member
 
2012GTCS's Avatar
 
Join Date: June 24, 2011
Location: Long Island
Posts: 1,568
Likes: 0
Received 0 Likes on 0 Posts
Hmm if they match the GT500 rear flaps I may get a set...
Old 6/21/12, 04:50 AM
  #29  
I Have No Life
 
FromZto5's Avatar
 
Join Date: September 24, 2011
Posts: 10,141
Received 172 Likes on 145 Posts
Originally Posted by 2012GTCS
Hmm if they match the GT500 rear flaps I may get a set...
That's the thing.I don't think they do.
Old 8/19/12, 08:43 PM
  #30  
Bullitt Member
 
mburnette's Avatar
 
Join Date: September 17, 2011
Posts: 209
Likes: 0
Received 1 Like on 1 Post
Just ordered
Old 8/20/12, 09:16 AM
  #31  
Cobra R Member
 
2012GTCS's Avatar
 
Join Date: June 24, 2011
Location: Long Island
Posts: 1,568
Likes: 0
Received 0 Likes on 0 Posts
Can anybody conform if they match the factory GT500 rears???????

Or pics with both in the pic. Thanks!
Old 8/20/12, 10:41 AM
  #32  
Bullitt Member
 
mburnette's Avatar
 
Join Date: September 17, 2011
Posts: 209
Likes: 0
Received 1 Like on 1 Post
I believe it's been stated before that they are not an exact match to the rears. Questions have been answered previously with pictures already posted. Start at the beginning of the thread and read on!
Old 8/20/12, 02:17 PM
  #33  
GT Member
 
outtaphase's Avatar
 
Join Date: April 17, 2012
Location: Connecticut
Posts: 115
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by 2012GTCS
Can anybody conform if they match the factory GT500 rears???????

Or pics with both in the pic. Thanks!
Here's some pics. Match or no match, I think they look great, and with most of my driveway being stone they are a must have!

Also, when you are driving down the road and come across a freshly paved one, they will protect you from the tar. Much easier to clean these than the side panels!





Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
austin101385
'10-14 Shelby Mustangs
3
10/2/15 01:00 PM
RoushRS3
2010-2014 Mustang
7
9/29/15 08:03 PM
Evil_Capri
2015 - 2023 MUSTANG
2
9/25/15 12:56 PM
tj@steeda
2015 - 2023 MUSTANG
0
9/16/15 06:44 PM



Quick Reply: '10-'13 Front Stone/Splash Guards



All times are GMT -6. The time now is 06:30 PM.