2001 Bullitt #3006
Haven't we been over this enough? 
1/6/09, 07:21 PM
#703
NTTAWWT
I really dont even wanna start pricing stuff for the 07 when I get it. I'm going to guess somewhere around 35k when/if I get it fully done like I want
That's a lot of dough!
1/12/09, 04:00 PM
#706
Post *****
Thread Starter
Join Date: May 13, 2004
Location: Berkeley/Redwood City, CA
Posts: 18,613
Likes: 0
Received 3 Likes
on
2 Posts
got that right. I've got some leftover cash from the insurance check. it was 1600 and some change. I'm using the 1000 to pay off part of the loan, and 500 of rhat is good for mods.
I had 170 saved in a drawer to ues to pay for the bikes wiring job, but thats not happening anymore
the bike is being sold for 200, a= nd im selling the gas tanks for 100
that puts me at 500+170+200+100=970
still trying to scrounge some more cash, but there are other car/bike parts sitting in the garage that need to get gone. I need a total of 1210, bec shipping is about $50, but I think its highly doable in the near future.
I had 170 saved in a drawer to ues to pay for the bikes wiring job, but thats not happening anymore
the bike is being sold for 200, a= nd im selling the gas tanks for 100
that puts me at 500+170+200+100=970
still trying to scrounge some more cash, but there are other car/bike parts sitting in the garage that need to get gone. I need a total of 1210, bec shipping is about $50, but I think its highly doable in the near future.
1/12/09, 04:11 PM
#707
Legacy TMS Member Pr
So the II won't be fixed?
1/12/09, 04:16 PM
#711
Post *****
Thread Starter
Join Date: May 13, 2004
Location: Berkeley/Redwood City, CA
Posts: 18,613
Likes: 0
Received 3 Likes
on
2 Posts
The II's parts are dirt cheap. I'm paying for just shipping on one, and 40+shipping on the other 
The back wont get done til i have money for that later. The front is almost done here. I'll still want a tubular K member brace and a MM steering shaft. ill get tubular A arms too, when the time comes. I just installed new control arms, so I'll let em stay for now, until i can afford the tubulars.
I want coilovers in the rear too, but some people say its not worth ot or that its bad if its not set up right. One thing for sure is I will have the aluminum adjustable steeda control arms, a panhard bar/torque arm setup from MM and maybe some lowering springs if i dont do coilovers right away. Petes got a set of unknown rear springs in his garage, and we're gonna test em on my car. If they lower it, i'll trade him my original bullitt control arms for em.
The back wont get done til i have money for that later. The front is almost done here. I'll still want a tubular K member brace and a MM steering shaft. ill get tubular A arms too, when the time comes. I just installed new control arms, so I'll let em stay for now, until i can afford the tubulars.
I want coilovers in the rear too, but some people say its not worth ot or that its bad if its not set up right. One thing for sure is I will have the aluminum adjustable steeda control arms, a panhard bar/torque arm setup from MM and maybe some lowering springs if i dont do coilovers right away. Petes got a set of unknown rear springs in his garage, and we're gonna test em on my car. If they lower it, i'll trade him my original bullitt control arms for em.
1/12/09, 04:20 PM
#713
Legacy TMS Member Pr
1/12/09, 04:30 PM
#720
Legacy TMS Member Pr
