Boss 302 Steering Wheel Into '05 GT!
#62
I got my wheel and interface put in, but when I try to program the buttons, nothing happens. I programmed the interface to #9 and it flashed 9 times, but after that, nothing.
Last edited by dgann3; 2/11/12 at 07:26 PM.
#65
Mach 1 Member
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
LOL Nevermind, I just found a guy on ebay that's got 25 of them...
When I looked for them a few weeks ago I didn't find any... I swear!
http://www.ebay.com/itm/FORD-MUSTANG...#ht_500wt_1074
When I looked for them a few weeks ago I didn't find any... I swear!
http://www.ebay.com/itm/FORD-MUSTANG...#ht_500wt_1074
#66
V6 Member
Join Date: February 18, 2012
Location: North Texas
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
LOL Nevermind, I just found a guy on ebay that's got 25 of them...
When I looked for them a few weeks ago I didn't find any... I swear!
http://www.ebay.com/itm/FORD-MUSTANG...#ht_500wt_1074
When I looked for them a few weeks ago I didn't find any... I swear!
http://www.ebay.com/itm/FORD-MUSTANG...#ht_500wt_1074
#69
V6 Member
Join Date: February 18, 2012
Location: North Texas
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
The stock one is just really, really tight, so it's a ***** to get off and then the aftermarket one is just hard to put on. I just really had to work with it. I used a bone folder (leather working tool) to work around the airbag and get it stuffed back in there. It wasn't "hard" per se, just time consuming.
#71
V6 Member
Join Date: February 18, 2012
Location: North Texas
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
First you drill out the rivets (three of them). Next you just have to work it off the airbag. It's just a hassle to get off. You'll need some kind of plastic tool like a wedge or something to work in there and work the rubber off the tabs at the back and then to help get it off the airbag. Then you just have to work the new one on. Once it's over the airbag, you have to press one side of the airbag plate down into the cover so that the long tab at the bottom can go in the slot on the cover. Then you press the other side down, pressing on the edge pressing down and towards the center to get the other side in. It's not complicated. It just takes patience. Once that's done, just use some pop rivets to resecure it and you're good to go. It's difficult getting it back in because the wiring for the new wheel is different and it gets in the way. I haven't wired mine up yet. I'm going to do it when I get my radio module to allow the wheel controls to work.
#73
V6 Member
Join Date: February 18, 2012
Location: North Texas
Posts: 80
Likes: 0
Received 0 Likes
on
0 Posts
#74
Got the wheel installed and the cruise is working great (2008) but now I am trying to get the audio controls working. I have the wpt 440's and an axxess and a PAC interface. Not having any luck, can anyone help? I have an AVIC X930BT head unit.
#76
Bullitt Member
![](https://themustangsource.com/forums/images/rank.gif)
Join Date: May 3, 2010
Location: So Cal
Posts: 430
Likes: 0
Received 0 Likes
on
0 Posts
#77
Haven't wired it yet. trying to find details on what wires to connect where. I got an email from tech support at Axxes and he said that the green wire needs to be grounded, and the yellow wire to the green/white in the ASWC. I will be trying that tomorrow.
#78
Bullitt Member
![](https://themustangsource.com/forums/images/rank.gif)
Join Date: May 3, 2010
Location: So Cal
Posts: 430
Likes: 0
Received 0 Likes
on
0 Posts
#80
Bullitt Member
![](https://themustangsource.com/forums/images/rank.gif)
Join Date: May 3, 2010
Location: So Cal
Posts: 430
Likes: 0
Received 0 Likes
on
0 Posts