v6 spinners- Eleanor got hurt.
Legacy TMS Member
Joined: October 8, 2005
Posts: 12,395
Likes: 29
From: Medina county, OH
Originally posted by Martimus@December 25, 2005, 11:01 AM
The BRS spinners ARE awesome
And Bob at BRS is really great to deal with!
The BRS spinners ARE awesome
And Bob at BRS is really great to deal with!
Agreed!
Bullitt Member
Joined: July 7, 2005
Posts: 460
Likes: 0
Bullitt Member
Joined: May 30, 2005
Posts: 419
Likes: 0
I took a quicker and much cheaper approach. I used a 2" Brass Sliding door handle on the inside of the spinners. You need to take the wheels off to install it, but once it's in place, there is no way to remove the spinners without removing the brass handles; and you can't do that without removing the wheel. The spinners can turn freely when on the car so you can get access to all of the wheel lugs.
Bullitt Member
Joined: May 30, 2005
Posts: 419
Likes: 0
Originally posted by EleanorsMine@December 26, 2005, 8:05 AM
Remember, I don't have bullitts. (yet)
Remember, I don't have bullitts. (yet)
I've seen similar mods with PVC pipe caps but I found that they did not fit as well. If you want, you can try other altenatives. I took one spinner with me to Home depot and tried several items that were of the same diameter as the inside ring on the back of the spinner. The brass door handles happened to be a perfect fit in my case..
It's a great mod and the door handles cost less then $3/pair at Home Depot. It's a good way to make sure the spinners never come off. (unless you want them to)
Thread Starter
After all these years,
My C/T still sucks!
My C/T still sucks!
Joined: May 5, 2004
Posts: 7,190
Likes: 0
From: Orlando(DP!) Florida
Originally posted by Big D@December 26, 2005, 10:08 PM
hey April next time that happens look for a coin wash :P and just spray the puke off..
hey April next time that happens look for a coin wash :P and just spray the puke off..
After much spraying and cleaning the vomit is almost out.
Won't happen again.
It has come to my attention I need a car for kids to ride in. My 12 year old can barely fit in back anymore.
FR500 Member
Joined: August 23, 2004
Posts: 3,153
Likes: 0
Originally posted by odiaz@December 26, 2005, 8:57 PM
It shouldn't matter. The brass door handle fits inside the spinner on the back side of the wheel. The idea is to keep the tabs from being able to be compressed. This keeps the tabs fully expanded and hence the spinner can not be pulle out as long as the brass door handle is holding them in place.
I've seen similar mods with PVC pipe caps but I found that they did not fit as well. If you want, you can try other altenatives. I took one spinner with me to Home depot and tried several items that were of the same diameter as the inside ring on the back of the spinner. The brass door handles happened to be a perfect fit in my case..
It's a great mod and the door handles cost less then $3/pair at Home Depot. It's a good way to make sure the spinners never come off. (unless you want them to)
It shouldn't matter. The brass door handle fits inside the spinner on the back side of the wheel. The idea is to keep the tabs from being able to be compressed. This keeps the tabs fully expanded and hence the spinner can not be pulle out as long as the brass door handle is holding them in place.
I've seen similar mods with PVC pipe caps but I found that they did not fit as well. If you want, you can try other altenatives. I took one spinner with me to Home depot and tried several items that were of the same diameter as the inside ring on the back of the spinner. The brass door handles happened to be a perfect fit in my case..
It's a great mod and the door handles cost less then $3/pair at Home Depot. It's a good way to make sure the spinners never come off. (unless you want them to)
If I go the spinner route again, it'll the BRS ones for sure
Thread
Thread Starter
Forum
Replies
Last Post
