Ponies on The Run (Again)
I'll be looking for a little more blingage, either polished or chrome (in 18's). But, that's later down the road.
Legacy TMS Member
Join Date: May 24, 2006
Location: San Diego
Posts: 7,409
Likes: 0
Received 0 Likes
on
0 Posts
That upgrade will cost a pretty penny, so I'll need a bit of a lead time to gather up the mad money.
I'm still up in the air on exactly what wheel to get. The tires will most likely be like Tom's BFG's or the triple nickels.
I'm still up in the air on exactly what wheel to get. The tires will most likely be like Tom's BFG's or the triple nickels.
Brian, how did the G2 project go?
Bullitt Member
Join Date: April 11, 2006
Location: South Austin Texas
Posts: 428
Likes: 0
Received 1 Like
on
1 Post
Actually, I am more curious on how they hold up. I've seen some that were done and after a while they look pretty nasty.
He's got your number Bill!
Team Mustang Source
it didn't. I got to a late start yesterday and realized I had too much crap to do yesterday and today still and I couldn't drive for 24 hours after they're painted, so I decided on doing the struts today. Which was going swimingly until I realized that I did not have a 20mm 1/2 drive (or any drive for that matter) to take off the spindle
I thought it was 19 and figured I was safe. Now starting early and ready to go, Sears opens at 10 there goes an hour. Great
I thought it was 19 and figured I was safe. Now starting early and ready to go, Sears opens at 10 there goes an hour. Great
Team Mustang Source
It does look sweet!
Bullitt Member
Join Date: October 13, 2004
Location: Kissimmee, FL
Posts: 302
Likes: 0
Received 0 Likes
on
0 Posts
My roush spoiler was attached with only 3m tape for side pieces. Never had a problem, even with people leaning on them. (my wife).
Cobra Member
Join Date: May 17, 2007
Location: Texa$
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
Funny I was thinking the same thing, here is a guy who cuts a shaker hole in the hood of his car, a big hole and he’s worried about a few tiny few holes
I'm surprised the 3M is strong enough to hold the side spoilers on. If one (or both) fail, it'll most likely happen on the highway!
Kinda embarrassing if that were to happen. I remember reading one guy's post on his fake hood scoop blowing off on the highway.
Cobra Member
Join Date: May 17, 2007
Location: Texa$
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
I wasn't too worried about drilling holes in the fender, just the fact that it had to be done.
I'm surprised the 3M is strong enough to hold the side spoilers on. If one (or both) fail, it'll most likely happen on the highway!
Kinda embarrassing if that were to happen. I remember reading one guy's post on his fake hood scoop blowing off on the highway.
I'm surprised the 3M is strong enough to hold the side spoilers on. If one (or both) fail, it'll most likely happen on the highway!
Kinda embarrassing if that were to happen. I remember reading one guy's post on his fake hood scoop blowing off on the highway.
Tasca Super Boss 429 Member
I have what looked like a full set of 1/2 drive sockets 12-22mm.
I double checked just 'cause you got me thinkin'...
I have no 20mm either. What's up with that???
Don't feel bad, I would have had the same problem.
It may be strong stuff, but so is wind resistance.
I don't recall what brand, but he's running 275's on all corners.
Cobra Member
Join Date: May 17, 2007
Location: Texa$
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
You won't have me around the next few days which I'm sure is going to make many of you smile (ha) Going into the hospital and hopefully I'll be home on Wed afternoon.
Be good boys