Midwest TMS'ers General Communication Thread
Shelby GT500 Member
Joined: October 9, 2006
Posts: 2,757
Likes: 1
From: It's tough in the jungle !
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
Legacy TMS Member
Joined: August 7, 2006
Posts: 16,113
Likes: 789
From: In Boredom
hey guys...new locks and keys on order now...should be here this weekend.
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
Legacy TMS Member
Joined: June 24, 2006
Posts: 2,501
Likes: 16
So Scott you find out what threw that code??? Last couple of days when I was in 1st gear the engine sounds were different. Almost like the clutch was slipping but it was still pullin fine. Came out of an off-site work meeting to go back to work and remembered I had put the rear seats down to load some things in the trunk a couple of days ago. I didn't hear the different engine sounds at all the rest of the day. I fixed it
. Going camping this weekend,,I hope.
. Going camping this weekend,,I hope.
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
So Scott you find out what threw that code??? Last couple of days when I was in 1st gear the engine sounds were different. Almost like the clutch was slipping but it was still pullin fine. Came out of an off-site work meeting to go back to work and remembered I had put the rear seats down to load some things in the trunk a couple of days ago. I didn't hear the different engine sounds at all the rest of the day. I fixed it. Going camping this weekend,,I hope.
. Going camping this weekend,,I hope.Nope..still don't know why I got the code yet. Drove the car last night and back into work this morning and it still has not came back. I would suspect it was a loose gas cap but it was tight when I checked it.
Cobra R Member
Joined: October 10, 2004
Posts: 1,627
Likes: 1
From: Location: Indy
Hey - speaking of codes, if you run an after market air filter, is it likely to cause code problems?
Reason I ask is that Indystang tried one of the Air Hogs filters and after about a week he said there was a code. He did not say what the code was. It was reset by the dealer.
I thought the engine controls would adjust / adapt to minor airflow changes...
He has a spare filter and I was thinking of trying it out.
Reason I ask is that Indystang tried one of the Air Hogs filters and after about a week he said there was a code. He did not say what the code was. It was reset by the dealer.
I thought the engine controls would adjust / adapt to minor airflow changes...
He has a spare filter and I was thinking of trying it out.
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
Hey - speaking of codes, if you run an after market air filter, is it likely to cause code problems?
Reason I ask is that Indystang tried one of the Air Hogs filters and after about a week he said there was a code. He did not say what the code was. It was reset by the dealer.
I thought the engine controls would adjust / adapt to minor airflow changes...
He has a spare filter and I was thinking of trying it out.
Reason I ask is that Indystang tried one of the Air Hogs filters and after about a week he said there was a code. He did not say what the code was. It was reset by the dealer.
I thought the engine controls would adjust / adapt to minor airflow changes...
He has a spare filter and I was thinking of trying it out.
Hey Chris,
If that airfilter allowed much more air flow than the stock filter I bet he got lean codes. I know when I first put on my C&L intake I drove in around for about 5 miles before I loaded the new tune (still running stock tune) and I got a CEL for "right bank lean" and "left bank lean" in that short time. These things are very sensitive to changes like that. And I drove the car to work and back again today (about 26 miles) and still no code.
Scott
Last edited by 70MACH1OWNER; Apr 24, 2008 at 02:32 PM.
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
Thread Starter
Legacy TMS Member
Joined: October 8, 2005
Posts: 12,395
Likes: 29
From: Medina county, OH
LOL I have no idea.... but probably won't try it anyway. Now, if I could just get the local dealer to stop calling me, telling me to come pay and pickup that other sensor I ordered hahahaaa
.
http://forums.bradbarnett.net/showthread.php?t=462388
Last edited by codeman94; Apr 24, 2008 at 03:13 PM.
Cobra Member
Joined: February 2, 2005
Posts: 1,221
Likes: 1
From: Aurora, IL
I installed my Eradispeed 14" rotors on the front of my car yesterday, works very well. This will do until next year when I do the full Brembo setup. I may need to get my tires re-balanced, have a little vibration in the wheel around 60 or so before I even touch the brakes, so I'm thinking the tires didn't balance properly.
Last edited by frdtch05gt; Apr 24, 2008 at 03:20 PM.
Legacy TMS Member
Joined: January 9, 2005
Posts: 6,982
Likes: 6
From: New Carlisle, Ohio (20 miles north of Dayton)
We're closing on both houses next wenesday..the 30th...and I take immiadiate posession of my new house....yet I have 7 days to move out of my old one....I'm having my piano moved next friday...thats also when my sweet new garage door opener if being installed! Here is a link to a pic and some fun I was having.
http://forums.bradbarnett.net/showthread.php?t=462388
http://forums.bradbarnett.net/showthread.php?t=462388
Cool Cody...What time on the 30th? I will try to make a note to think about you than when I am laying on the beach at Marco Island, Florida sucking down a cold one. I will even drink one for you.
4:30pm...eastern time! Thanks!