What did you do with your Mustang today?
I change out the dash cluster because my original one wasn't dictating miles or trip. Sooo... the car wouldn't start. So I swapped out the board and had found out it was related to the key that starts the car. Car starts fine and the digital mile counter read outs with replacement cluster. I also found some like new headlights and they polished up nice and found a very clean trunk mat.
The following users liked this post:
Stage_3 (8/19/18)
THE RED FLASH ------ Master-Moderator
Marilyn looking badass as always, Burton
The following users liked this post:
FromZto5 (8/20/18)
Legacy TMS Member
Took my car out yesterday on a nice day trip with the wife. Went up to Littleton NH, about 2 hours each way.
Ended up putting more than 300 miles on it, and we had a great time doing it
Ended up putting more than 300 miles on it, and we had a great time doing it
Last edited by Gabe; 8/20/18 at 07:46 AM.
The following users liked this post:
m05fastbackGT (8/20/18)
THE RED FLASH ------ Master-Moderator
Looking awesome as always, Gabe.
The following users liked this post:
Gabe (8/20/18)
I Have No Life
Actually, both my 4:10 and 3:55 calculations were way off, Burton. Apparently what went wrong was that I didn't realize I had the wrong revs per mile selected for my tire size in the SCT X4 programmer. Anyhow after reflashing in the correct revs per mile, my actual cruising speeds with 3:55 axle ratio were 55 mph between 1500-1800 rpm in 5th gear and then 60 mph at around 1900 rpm in 5th gear and then finally 75 mph at 2400 rpm in 5th gear. At any rate, I should have definitely paid more attention to say the very least lol.
Marilyn looking badass as always, Burton
Marilyn looking badass as always, Burton
Roush Forum Stalker
Legacy TMS Member
Legacy TMS Member
Yesterday attended a show raising money for retired NH State Police K9's:
The following 2 users liked this post by Gabe:
m05fastbackGT (9/2/18),
Stage_3 (8/27/18)
The following users liked this post:
Gabe (8/27/18)
The following users liked this post:
Stage_3 (8/31/18)
I had the front end aligned which made a huge difference, the toe was out a bit. Then I installed a new set of pads and clips on the rear rotors. Changed oil in all my vehicles and found some issues,one of the serpentine belts was starting to break apart so I replaced that.I inspect everything when I open the hood or raise the car, preventative maintenance can save you big money and time.
Super Boss Lawman Member
I changed the oil, filter, ProCharger oil, and air filter today, then gave it a much needed wash since it rained here 5 days in a row. Also changed the oil on my wife's Saturn and did a headlight restore on it.
The following users liked this post:
Stage_3 (9/10/18)
Car is in the shop I have a question to everyone ? Any one having a popping noise coming from the rear end when they go to accelerate from a dead stop or shifting gears if you have a manual at slower speeds? If so what fixed the problem?
Royal Crimson GT PP1 Member
https://performanceparts.ford.com/do...htM-4130-M.pdf
also check out this video, event hough it covers more then you need:
Last edited by 1 old racer; 9/10/18 at 09:28 PM.
Like Father...
I ♥ Sausage
I ♥ Sausage
The following users liked this post:
1 old racer (9/12/18)
The following users liked this post:
Stage_3 (9/13/18)
Roush Forum Stalker