MMD Sat Radio Antenna Cover
4/29/13, 09:20 PM
#22
Cobra R Member
4/30/13, 10:36 PM
#23
Member
Join Date: March 16, 2013
Posts: 42
Likes: 0
Received 0 Likes
on
0 Posts
i thought about this piece as well, however, my car is black. and between that and the larger CS spoiler i dont know if it would be a much of a chance. i may do it once i get to the point when im just doing little finishing touches to the car.
5/1/13, 03:39 PM
#24
Here it is out of the box. It's between 1/2 to 3/4 inch bigger in all dimensions than the antenna itself, to allow for a 1/4 inch lip to hold the adhesive:
For comparison to the antenna itself:
For comparison to the antenna itself:
Last edited by DRB; 5/1/13 at 09:05 PM.
5/1/13, 08:57 PM
#26
Banned
Join Date: July 4, 2012
Location: Washington, DC
Posts: 2,983
Likes: 0
Received 0 Likes
on
0 Posts
5/1/13, 09:02 PM
#27
and why wouldn't it work? I'll just put it over them.
5/1/13, 10:24 PM
#28
Mach 1 Member
Join Date: October 17, 2012
Location: Culver City, CA
Posts: 526
Likes: 0
Received 4 Likes
on
4 Posts
It fits, but they're still trying to work out the gaps under the taillights. Once done, they're going to paint the decklid panel black to match and mask the gaps. Probably another week before they're done with the back and then they can finish the front.
5/2/13, 02:20 AM
#29
Cobra R Member
5/2/13, 07:20 AM
#30
I haven't actually installed it - tomorrow, after I clean the car up a bit.
I like the look; the paint match is good. Guess I wish it were a little closer in size to the antenna but it takes what it takes.
I like the look; the paint match is good. Guess I wish it were a little closer in size to the antenna but it takes what it takes.
5/2/13, 07:43 AM
#31
Cobra R Member
5/2/13, 09:48 AM
#32
It's probably the best size they can practically make it. You can judge from the photo - I'm being a nitpicker; it does look a lot better than the black antenna.
Last edited by DRB; 5/2/13 at 09:50 AM.
8/1/14, 08:29 PM
#36
Yes, I'm still happy with mine - more so as I've gotten used to it.
I'll try to remember to measure it tomorrow. I'd say it adds 3/8 to 1/2 inch to the width and length of the antenna.
I'll try to remember to measure it tomorrow. I'd say it adds 3/8 to 1/2 inch to the width and length of the antenna.
8/1/14, 10:42 PM
#37
Thank you
8/1/14, 11:38 PM
#38
GT Member
I bought the CPC "shark fin" antenna cover:
http://www.cjponyparts.com/cpc-trunk...014/p/ANTC1-V/
I got it "free" using a gift card from wheel purchase a while back.
http://www.cjponyparts.com/cpc-trunk...014/p/ANTC1-V/
I got it "free" using a gift card from wheel purchase a while back.
Last edited by VIP1; 8/1/14 at 11:47 PM.
8/2/14, 12:02 AM
#39
Legacy TMS Member
I bought the CPC "shark fin" antenna cover: http://www.cjponyparts.com/cpc-trunk...014/p/ANTC1-V/ I got it "free" using a gift card from wheel purchase a while back.
