Jackpoint Jack Stands
#1
Bullitt Member
Thread Starter
Jackpoint Jack Stands
Like many other people on the site I was perplexed where to put jack stands to work on the car. Jack from pumpkin, don't jack from pumpkin, put stands here, don't put them there. Use wood, don't use wood. Also whenever I used jack stands on previous cars they always seemed to get in the way. I saw these on an episode of Jay Lenos garage and knew they were the answer. Jackpoint Jack Stands. Consists of a disc and collar. Disc goes on Floor jack. The disc fits onto the pinch weld at the factory jacking points. Lift car up, slide collar around jack and lower disc onto collar. Car is on the stands and 100% secure. Much more so than regular jack stands. At $299 they are real expensive but after using them are worth every penny. They are a solid casting unlike regular jack stands.
I know there will be a ton of people going $299 for jack stands are you crazy. Check them out on youtube. Watch them on Jay Lenos garage. After using them I can say they are worth every penny. Will be getting a 2nd set so I can get entire car off the ground. Also just a note for people that have it, these clear the boss side pipes no problem.
http://jackpointjackstands.com/
http://shop.jackpointjackstands.com/
image hosting
how to do a screenshot on a pc
adult image
I know there will be a ton of people going $299 for jack stands are you crazy. Check them out on youtube. Watch them on Jay Lenos garage. After using them I can say they are worth every penny. Will be getting a 2nd set so I can get entire car off the ground. Also just a note for people that have it, these clear the boss side pipes no problem.
http://jackpointjackstands.com/
http://shop.jackpointjackstands.com/
image hosting
how to do a screenshot on a pc
adult image
Last edited by imeyers302; 4/26/15 at 06:54 AM.
#4
Bullitt Member
Thread Starter
They are a fixed height, however they bring car up as high as normal jack stands would and you can buy additional discs which stack on top to add height if you want car higher. Even changing a tire is easier. Just use floor jack and disc and lift from factory jack point.
#5
Bullitt Member
Thread Starter
#6
Mach 1 Member
Those are nice and look to be well made. I'll be one of those guys $299 for jack stands, and $600 for a set, are you crazy?? You would have to be Jay Leno to afford them.
#7
Legacy TMS Member
Those are indeed nice.
However, I frequently use my 2 ton jack stands on the pinch welds as you would the jack. Never had a problem with that. You jack the car up on the regular jack points, and then you slide the jack stand as close to the jack as possible, lower it. Done. Stable and fine, never an issue. As good as a lift in the same places.
IF I come into a ton of money, I'll buy these. But I can't, that's mod money.
However, I frequently use my 2 ton jack stands on the pinch welds as you would the jack. Never had a problem with that. You jack the car up on the regular jack points, and then you slide the jack stand as close to the jack as possible, lower it. Done. Stable and fine, never an issue. As good as a lift in the same places.
IF I come into a ton of money, I'll buy these. But I can't, that's mod money.
#8
Bullitt Member
Thread Starter
Those are indeed nice.
However, I frequently use my 2 ton jack stands on the pinch welds as you would the jack. Never had a problem with that. You jack the car up on the regular jack points, and then you slide the jack stand as close to the jack as possible, lower it. Done. Stable and fine, never an issue. As good as a lift in the same places.
IF I come into a ton of money, I'll buy these. But I can't, that's mod money.
However, I frequently use my 2 ton jack stands on the pinch welds as you would the jack. Never had a problem with that. You jack the car up on the regular jack points, and then you slide the jack stand as close to the jack as possible, lower it. Done. Stable and fine, never an issue. As good as a lift in the same places.
IF I come into a ton of money, I'll buy these. But I can't, that's mod money.
image hosting no registration
upload picture
image share
Last edited by imeyers302; 4/26/15 at 01:24 PM.
#10
Bullitt Member
Thread Starter
#11
Where do you guys lift to get all 4 wheels off the ground?
#12
Mach 1 Member
Center of differential in back and center of cross member in front. I'm sure there will be plenty of folks here who will tell you how wrong or bad that is but my car is three years old, has been jacked more times than I can count and nothing is bent and recent 4 wheel alignment says everythings good to go.
John
John
#13
Legacy TMS Member
As long as it's stable, doesn't bend, anywhere on the car is technically a good jacking point. Axle center, axle near ends, pinch welds front, back, and even center, hard mount points for any suspension location...
As with any jacking, using stands, or ramps, *always be safest you can be*. 1.5 - 2 tons is nothing to mess around with when it's not on the wheels. And CHOCK THE WHEELS. Rolling off a jack is not fun.
---
In regards to the 'jack stand failure' Googlin'... I did. there's plenty of doom and gloom. But not nearly as much as you'd think, IMO. There's also jack failure, and all kinds of things. Heck, I had a scissors jack fail me and the car rolled... **** near lost a finger. Did loose some skin. It grew back, though.. Fingertips are interesting like that.
Point is... the car, whenever it's in the air, is out to kill you. Or at least, you should consider it is, anyway.
Now, as to MY jack stands... I don't buy junk. The stuff that fails is the cheapest crap out there, and you should prepare to die every time you use it. The riveted 1.5 ton sheet metal tri stands, for one. Horrid.
Solid, heavy metal, hopefully not Chinese steel ('cause it's just not as good, the impurities in it), and oh yes, if it's old... TIME FOR A NEW SET.
I replace mine every few years. If they look tired... they are. They're cheap to acquire good ones, so DO IT.
You all do what you want to, just be safe... and if you don't feel safe? You aren't. Fix it.
As with any jacking, using stands, or ramps, *always be safest you can be*. 1.5 - 2 tons is nothing to mess around with when it's not on the wheels. And CHOCK THE WHEELS. Rolling off a jack is not fun.
---
In regards to the 'jack stand failure' Googlin'... I did. there's plenty of doom and gloom. But not nearly as much as you'd think, IMO. There's also jack failure, and all kinds of things. Heck, I had a scissors jack fail me and the car rolled... **** near lost a finger. Did loose some skin. It grew back, though.. Fingertips are interesting like that.
Point is... the car, whenever it's in the air, is out to kill you. Or at least, you should consider it is, anyway.
Now, as to MY jack stands... I don't buy junk. The stuff that fails is the cheapest crap out there, and you should prepare to die every time you use it. The riveted 1.5 ton sheet metal tri stands, for one. Horrid.
Solid, heavy metal, hopefully not Chinese steel ('cause it's just not as good, the impurities in it), and oh yes, if it's old... TIME FOR A NEW SET.
I replace mine every few years. If they look tired... they are. They're cheap to acquire good ones, so DO IT.
You all do what you want to, just be safe... and if you don't feel safe? You aren't. Fix it.
Last edited by houtex; 4/26/15 at 06:39 PM.
#14
These do look really nice and sturdy. I wish they went up a little higher than 12" without the spacer since I am a little thick in the middle. I really do think I would feel safe with those under my car though. I have been looking at the quickjack lately but I am not sure how reliable the locking mechanism is for a long term project with the wheels off.
http://www.quickjack.com/
http://www.quickjack.com/
#15
If you're truly paranoid nothing beats wheel cribs. Unless you need to take the wheels off, then you're screwed.
+1 on the chocks.
Another approach is to use jack stands, but back them up with a solid object (some people use the wheel) that is taller than your height lying down, which the car would land on if the stand fails. I would imagine a suitable height block could be created with plywood or 2x4 layers.
+1 on the chocks.
Another approach is to use jack stands, but back them up with a solid object (some people use the wheel) that is taller than your height lying down, which the car would land on if the stand fails. I would imagine a suitable height block could be created with plywood or 2x4 layers.
#16
Mach 1 Member
As long as it's stable, doesn't bend, anywhere on the car is technically a good jacking point. Axle center, axle near ends, pinch welds front, back, and even center, hard mount points for any suspension location... As with any jacking, using stands, or ramps, *always be safest you can be*. 1.5 - 2 tons is nothing to mess around with when it's not on the wheels. And CHOCK THE WHEELS. Rolling off a jack is not fun. --- In regards to the 'jack stand failure' Googlin'... I did. there's plenty of doom and gloom. But not nearly as much as you'd think, IMO. There's also jack failure, and all kinds of things. Heck, I had a scissors jack fail me and the car rolled... **** near lost a finger. Did loose some skin. It grew back, though.. Fingertips are interesting like that. Point is... the car, whenever it's in the air, is out to kill you. Or at least, you should consider it is, anyway. Now, as to MY jack stands... I don't buy junk. The stuff that fails is the cheapest crap out there, and you should prepare to die every time you use it. The riveted 1.5 ton sheet metal tri stands, for one. Horrid. Solid, heavy metal, hopefully not Chinese steel ('cause it's just not as good, the impurities in it), and oh yes, if it's old... TIME FOR A NEW SET. I replace mine every few years. If they look tired... they are. They're cheap to acquire good ones, so DO IT. You all do what you want to, just be safe... and if you don't feel safe? You aren't. Fix it.
Now aluminum on the other hand will fatigue and there is no way to predict when aluminum will fail. Steel however can last a lifetime.
#18
Legacy TMS Member
Awesome concept. They are expensive imo. Agree with the statement about putting a secondary safety measure in there like the tire under the car. I find jack stands almost always get in the way but they are a must.
#20
Shelby GT350 Member
isn't it bad on the frame to lift the car one corner at a time? I just don't see how that doesn't put a lot of stress on the frame. That's why I lift with the crossmember in the front. Total pain in the *** though...have to drive up ramps, get a jack and jack it higher than the ramps, remove ramps, then remove wheels (if necessary)
Last edited by Coyote5-0; 4/29/15 at 07:28 AM.