GT 500 mufflers on my 2011 GT, now with video
11/27/10, 07:14 PM
#101
Member
Join Date: July 20, 2010
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
According to one guy the pinks episodes are running one to two months behind the actual run date - a new one every Thurs. Also it is questionable if Pinks will air next year due to lack of sponsors and money - and I though it was doing so good.
Taking a look at Lethal Performance - Offroad H-Pipe. This might be a nice combo with the GT500 muffs and stock shorty headers !
http://www.lethalperformance.com/201...905_9908_10274
Taking a look at Lethal Performance - Offroad H-Pipe. This might be a nice combo with the GT500 muffs and stock shorty headers !
http://www.lethalperformance.com/201...905_9908_10274
11/29/10, 03:12 PM
#102
Member
Join Date: July 20, 2010
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
GT500 Muffer Tip Alignment (Front to Back):
Has anyone felt that the stainless tips need to come back just a bit, loosen the forward pipe band clamps to move it back a half inch or so. The inside edge (middle) sits back approx. 1.25 inch in from the outer edge of the black facia. The outer edge is fine at approx. .75 out from the black facia. I don't think they look bad but the inner edge might be a bit too far forward. Thanks, Bill
Has anyone felt that the stainless tips need to come back just a bit, loosen the forward pipe band clamps to move it back a half inch or so. The inside edge (middle) sits back approx. 1.25 inch in from the outer edge of the black facia. The outer edge is fine at approx. .75 out from the black facia. I don't think they look bad but the inner edge might be a bit too far forward. Thanks, Bill
Last edited by billaz5.0; 11/29/10 at 03:19 PM. Reason: Sp.
11/29/10, 10:12 PM
#103
I am Shauny Clause
MOTM July 2010 Winner
MOTM July 2010 Winner
Join Date: November 25, 2009
Location: Metro Detroit
Posts: 1,519
Likes: 0
Received 0 Likes
on
0 Posts
GT500 Muffer Tip Alignment (Front to Back):
Has anyone felt that the stainless tips need to come back just a bit, loosen the forward pipe band clamps to move it back a half inch or so. The inside edge (middle) sits back approx. 1.25 inch in from the outer edge of the black facia. The outer edge is fine at approx. .75 out from the black facia. I don't think they look bad but the inner edge might be a bit too far forward. Thanks, Bill
Has anyone felt that the stainless tips need to come back just a bit, loosen the forward pipe band clamps to move it back a half inch or so. The inside edge (middle) sits back approx. 1.25 inch in from the outer edge of the black facia. The outer edge is fine at approx. .75 out from the black facia. I don't think they look bad but the inner edge might be a bit too far forward. Thanks, Bill
11/30/10, 02:31 PM
#104
Member
Join Date: July 20, 2010
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Done - looks much better ! Once aligned I tried to center the band clamp with respect to the now larger gap but it would not move easilly so just tightened back up - hoping it still has enough area to catch the band clamp surface. Thanks.
12/22/10, 08:36 PM
#106
Member
Join Date: July 20, 2010
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
Another video/audio:
http://www.youtube.com/watch?v=UD58WGi6mMo
http://www.youtube.com/watch?v=UD58WGi6mMo
Thread
Thread Starter
Forum
Replies
Last Post