Shotokan1509

Ok

#1, no making fun of the dirty car!

Few backside pics, you can see the clips holes I was speaking of, and how far the inlet protrudes to the backside. Those washers are bigger than supplied, due to me having to extend some of the holes for good fit.



From the front, you can see how closely I can get it all put together with the SHR grille... for some reason the light is really showing through over the top of the grill in the pic, it is extremely close in person so disregard that.








You opened a discussion you don't want, I debated for a long time.. heres different setups in the link, although all except the factory pieces would require some cutting.

http://rides.webshots.com/album/576258608XGDOeX

ThatMattGuy

Thank you for the pictures, I appreciate it! Those cuts might not be too bad, a friend of mine has a little shop so maybe he can help me..I just don't want to screw anything up. It might also be a bit easier because the bumper isn't on my car yet, so I could do it before I put it on..also thanks for the link!

Shotokan1509

I would say quite a bit easier from the back side with bumper not installed.

ThatMattGuy

Well I'll let you guys know how it goes, I also decided on the ford Bullet grille for the upper grille, it's also the deal if the day on partscheap so I guess I got lucky with that.

2k7gtcs

Matt

I have the exact setup you are about to do. I also have those lower side pieces that I won't need anymore.

I will post up later when I get home.

ThatMattGuy

Another question I probably should have asked before buying the bumper, but I can put it on re using the clips from my v6 bumper...right...?

2k7gtcs

I think the foam piece that attaches to the actual metal bumper and helps to keep the bumper cover formed is different. Did you get that piece?

I don't know it for fact, but mine was labeled "GT" so I figured it might be different for a V6?

Anyone know this?

2k7gtcs

ThatMattGuy

No I didn't get that piece....the bumper won't be ready until tomorrow or Friday, and then I'm going to have to wait until my upper grille comes in before I put it on..should I order it from the Ford dealer? I know Ford brands some parts GT or V6 but in reality they are the EXACT same..

2k7gtcs

I don't even know that you need it for sure.

I've never seen the bumper cover off of a V6 to be able to see the difference.

ThatMattGuy

Well I hope I don't need it, I want to get the bumper on ASAP..

Shotokan1509

You may also need some of the trim under the car.. the flat black plastic you can see to the left in my first 3 photos

ricksGT/CS

Go ,,Shelby ,,brake dusts and lowerr grille ,,,,just saying ,,,

ThatMattGuy

Could you show me what pieces? And are there part numbers for them?
If any V6 guys out there have swapped to a GT bumper please give me some help..

ThatMattGuy

Well that does look nice, but I already ordered the ford bullet grille, and SHR lower grille, maybe on the cars next "refresh" (new bumpers, lights, etc) but that wont be for a few years, and then it's going all out, custom complete paint job, engine swap, interior swap, all new bumpers, suspension, rails, anything that has rusted, hood...it will be expensive, but I love this car, and even if it cost 15-20k, that's fine with me, because I will be bringing new life into this car, just as if I had bought a new one. That's just my thoughts..

ThatMattGuy

Alright, after even more research I have found this list...if anyone can help me verify this I would be thankful. They also were talking about needing new fender liners?

Part Number : Qty : Description: Price
5R3Z-17626-BA : 1 : DEFLECTOR - STONE : $22.76
5R3Z-16102-BA : 1 : GUARD - FRONT SPLASH : $11.82
5R3Z-16103-BA : 1 : GUARD - FRONT SPLASH : $7.13
5R3Z-17C947-BA : 1 : FOAM BUMPER ISOLATOR : $7.00
N801169S900 : 1 : PACK OF EIGHT SCREWS : $4.00
W705992S441 : 1 : PACK OF FOUR INSERTS : $4.00

Thanks guys, I'm trying to get this done as fast as possible and try to save some money...I appreciate y'all taking the time to help a guy out!

EDIT: I have also found the part numbers for the OEM GT/CS lower grille inserts, for anyone who is interested-

part #'s
7R3Z-17E810-AA (RH)
7R3Z-17E811-AA (LH)

ThatMattGuy

I got my bumper in today! Here is a picture!

SilverHorse-----Racing

Ah, the days of car parts on the couch... I remember that!

ThatMattGuy

Well it's the only place it will fit. Atleast the upper grille install will be easy..I'm pretty sure it just snaps on there.

Shotokan1509

Sweet, replacing the orange blinkers while in there?