05-09 Exterior Modifications Making Your '05 Stand Out from the Crowd

Lowered with Steeda springs.

Thread Tools
 
Search this Thread
 
Old Oct 12, 2005 | 10:25 PM
  #1  
Firedude's Avatar
Thread Starter
Bullitt Member
 
Joined: April 3, 2005
Posts: 318
Likes: 0
I have a couple pics of my stang with the Steeda springs.
Reply
Old Oct 13, 2005 | 04:38 AM
  #2  
2005RedGT's Avatar
Cobra Member
 
Joined: November 13, 2004
Posts: 1,431
Likes: 0
Looks Good.

-Bryan
Reply
Old Oct 13, 2005 | 05:17 AM
  #3  
jwgroovin's Avatar
Mach 1 Member
 
Joined: February 15, 2005
Posts: 639
Likes: 3
Originally posted by Firedude@October 13, 2005, 12:28 AM
I have a couple pics of my stang with the Steeda springs.
Man that looks good. I just ordered Steeda springs because of the sligher 1" drop, but your side shot has me worried that my chin spoiler will become speed bump fodder. If you get a chance, I'd appreciate a closeup from the side so I can see the front spoiler clearance a bit better.

Nice looking ride!

John
Reply
Old Oct 13, 2005 | 06:32 AM
  #4  
Budders's Avatar
Bullitt Member
 
Joined: July 24, 2005
Posts: 512
Likes: 0
looks good, you got any bigger pics?
Reply
Old Oct 13, 2005 | 06:34 AM
  #5  
MeanStang's Avatar
Bullitt Member
 
Joined: April 18, 2004
Posts: 346
Likes: 0
jwgroovin - remember steeda has their own chinspoiler type thing.. an the clearance is fine
Reply
Old Oct 13, 2005 | 10:36 AM
  #6  
Firedude's Avatar
Thread Starter
Bullitt Member
 
Joined: April 3, 2005
Posts: 318
Likes: 0
Thanks for the good words. The chin is 6 1/2 inches at its lowest point. Don't know if these pics help. I will try and get a couple more latter. Those headers you see in the back round are going on today.
Reply
Old Oct 13, 2005 | 10:41 AM
  #7  
Firedude's Avatar
Thread Starter
Bullitt Member
 
Joined: April 3, 2005
Posts: 318
Likes: 0
Two in the garage.
Reply
Old Oct 13, 2005 | 11:19 AM
  #8  
jwgroovin's Avatar
Mach 1 Member
 
Joined: February 15, 2005
Posts: 639
Likes: 3
Originally posted by Firedude@October 13, 2005, 12:39 PM
Thanks for the good words. The chin is 6 1/2 inches at its lowest point. Don't know if these pics help. I will try and get a couple more latter. Those headers you see in the back round are going on today.
My CDC Classic Chin Spoiler is 6" from the ground at the lowest point, so another inch won't make all that much difference, I suppose. No guts no glory...
Reply
Old Oct 13, 2005 | 07:44 PM
  #9  
Firedude's Avatar
Thread Starter
Bullitt Member
 
Joined: April 3, 2005
Posts: 318
Likes: 0
Go for it . You are going to like the look.
Reply
Old Oct 13, 2005 | 09:01 PM
  #10  
hawgman's Avatar
Cobra Member
 
Joined: March 30, 2005
Posts: 1,122
Likes: 0
How is the ride? I know that answer is going to be subjective to the owner, but honestly..how is the ride?
Reason I ask. I took a road trip with a friend last weekend who installed the Ebiachs. After about 3 hours of driving I was VERY READY to get to our destination. Was quite disappointed in how stiff it was.
Reply
Old Oct 13, 2005 | 09:20 PM
  #11  
Rubbermonkey's Avatar
GT Member
 
Joined: June 27, 2005
Posts: 119
Likes: 1
Nice amount of drop, planning on getting the steedas as well.
Reply
Old Oct 13, 2005 | 09:52 PM
  #12  
Budders's Avatar
Bullitt Member
 
Joined: July 24, 2005
Posts: 512
Likes: 0
How is the ride?
The dampers affect the ride more so than the springs, so if you put on new dampers tuned to the news springs the ride would probably be the same as stock
Reply
Old Oct 14, 2005 | 07:06 PM
  #13  
Firedude's Avatar
Thread Starter
Bullitt Member
 
Joined: April 3, 2005
Posts: 318
Likes: 0
The ride is stiffer. Not too much more than stock but noticeable for sure.
Reply
Old Oct 15, 2005 | 10:21 AM
  #14  
Driver's Avatar
GT Member
 
Joined: October 11, 2004
Posts: 107
Likes: 0
I put the UPR (made by Eibach for UPR) on my 05 gt 200.00 to my door by the way.I had ford install them when they had the front struts off replacing the Defective Bearing that made that terrible popping noise. When Ford aliened the front end back up they used a cam bolt for the camber and caster adjustment. Only the driver side needed the cam bolts. The Two cam bolts came in one package for 25 bucks. anyway Sorry to be so long winded but the Ride is still as good as before,the steering is more responsive and the Look is GREAT.
Reply
Old Oct 15, 2005 | 01:00 PM
  #15  
BuzzyStang05's Avatar
Team Mustang Source
 
Joined: April 8, 2004
Posts: 765
Likes: 1
What size wheels/tires you running there?
Reply
Old Oct 15, 2005 | 05:29 PM
  #16  
Firedude's Avatar
Thread Starter
Bullitt Member
 
Joined: April 3, 2005
Posts: 318
Likes: 0
Originally posted by BuzzyStang05@October 15, 2005, 1:03 PM
What size wheels/tires you running there?
Not sure if this question was for me but my tires are in my sig.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
austin101385
'10-14 Shelby Mustangs
3
Oct 2, 2015 01:00 PM
tj@steeda
Auto Shows and Events
0
Sep 30, 2015 07:02 PM
GeoWett
GT
3
Sep 30, 2015 06:40 AM
tj@steeda
2015 - 2023 MUSTANG
0
Sep 24, 2015 08:15 PM




All times are GMT -6. The time now is 04:10 AM.