anti-freeze is done, dyno date is set!
#1
Member
Thread Starter
Join Date: August 23, 2008
Location: NY
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
anti-freeze is done, dyno date is set!
Hey guys & gals,
The guy that put my Vortech V3 after-charge cooler, didn't put any anti-freeze in the cooler tank just water. And now that its cold here in NY the water was freezing up, so I got the anti-freeze put in yesterday before any problems arise. The work was done at Mustang Magic on New York,LI and they did a very messy job with anti-freeze all over the place. So today I'll go outside to see if anything is leaking.
I have a dyno date for 12-20-08
I been running my ride on the canned tune from Vortech for about 3-4 months and I think everything is still OK with the ride.
Wish me luck, please!
Thank you, all!
Denny
The guy that put my Vortech V3 after-charge cooler, didn't put any anti-freeze in the cooler tank just water. And now that its cold here in NY the water was freezing up, so I got the anti-freeze put in yesterday before any problems arise. The work was done at Mustang Magic on New York,LI and they did a very messy job with anti-freeze all over the place. So today I'll go outside to see if anything is leaking.
I have a dyno date for 12-20-08
I been running my ride on the canned tune from Vortech for about 3-4 months and I think everything is still OK with the ride.
Wish me luck, please!
Thank you, all!
Denny
#4
Member
Thread Starter
Join Date: August 23, 2008
Location: NY
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
Hey Guys!
The dyno was pushed back because of the snow we had here in NYC
The new date is Jan. 3, 2009 this Sat. coming up.
Sorry about the no update on this subject, but in internet was all f-ed-up!
And the dyno time is all readly paid for. So we shell see what happen on Sat.
I'm looking for around 270-300 on the 8-10lbs pulley, wish me luck guys!
The Polish Snail!
The dyno was pushed back because of the snow we had here in NYC
The new date is Jan. 3, 2009 this Sat. coming up.
Sorry about the no update on this subject, but in internet was all f-ed-up!
And the dyno time is all readly paid for. So we shell see what happen on Sat.
I'm looking for around 270-300 on the 8-10lbs pulley, wish me luck guys!
The Polish Snail!
#5
Member
Thread Starter
Join Date: August 23, 2008
Location: NY
Posts: 37
Likes: 0
Received 0 Likes
on
0 Posts
I went for dyno to tune my V3 S/C, check out with happen!
Hey People,
So I go for the dyno Sat, 3. 2009! They lock my baby down to the MD dyno, then they did a warm up pull, baby made 245wrhp w/stock tune from Vortech! Not bad for a stock tune! Coming down from the pull speed, Dan hears some noise coming from the rear axle of the car! HERE WE GO! Bearings in the rear-end are shot, he says to me! OK!
We took baby off the dyno and shipped her over to the lift, crack open the differential cover!
And for sure we have a broken left side shim still around the axle but broke in 3 parts, all 4 bearings had to be replace, the front/rear and 2 side bearings had to be replace for the wear on the little wheels.
I had 2 people tell me about this problem, the first guy that put the S/C'er in the ride said to me your car don't sound to good in the rear axle. The second guy that did my dual exhaust setup said the same thing.
So I still have no tune and a bill for 550.00, so the rear-end is done and I know baby is running 245, Oh well! Thats life!
I have a new date for the dyno, 1/17/09
One very sad story! What do you guys&gals think??????????????
The owner of a Polish Snail!
So I go for the dyno Sat, 3. 2009! They lock my baby down to the MD dyno, then they did a warm up pull, baby made 245wrhp w/stock tune from Vortech! Not bad for a stock tune! Coming down from the pull speed, Dan hears some noise coming from the rear axle of the car! HERE WE GO! Bearings in the rear-end are shot, he says to me! OK!
We took baby off the dyno and shipped her over to the lift, crack open the differential cover!
And for sure we have a broken left side shim still around the axle but broke in 3 parts, all 4 bearings had to be replace, the front/rear and 2 side bearings had to be replace for the wear on the little wheels.
I had 2 people tell me about this problem, the first guy that put the S/C'er in the ride said to me your car don't sound to good in the rear axle. The second guy that did my dual exhaust setup said the same thing.
So I still have no tune and a bill for 550.00, so the rear-end is done and I know baby is running 245, Oh well! Thats life!
I have a new date for the dyno, 1/17/09
One very sad story! What do you guys&gals think??????????????
The owner of a Polish Snail!
Last edited by dennycarlton; 1/5/09 at 12:19 PM.
Thread
Thread Starter
Forum
Replies
Last Post