FAST intake manifod
2/7/07, 11:16 PM
#1
Bullitt Member
Thread Starter
Join Date: January 28, 2007
Posts: 362
Likes: 0
Received 0 Likes
on
0 Posts
FAST intake manifod
Has anyone got any info on this bolt on?
Sposed to add a honest 40hp, but was in the development stage at press time. They had one in their booth at SEMA but no info on their crazy *** website.
Thanks,
Sposed to add a honest 40hp, but was in the development stage at press time. They had one in their booth at SEMA but no info on their crazy *** website.
Thanks,
2/7/07, 11:38 PM
#2
Former Vendor
Join Date: January 11, 2007
Location: Aston, PA
Posts: 2,594
Likes: 0
Received 0 Likes
on
0 Posts
I got a buddy at comp cams I can call and have him ask about it. I'm sure he knows somebody in the FAST department? I'll call tomorrow during the day sometime.
2/8/07, 12:05 AM
#3
Bullitt Member
Join Date: August 8, 2006
Posts: 201
Likes: 0
Received 0 Likes
on
0 Posts
Theres not really much released yet, heres a bit of info http://www.fordmuscle.com/blog/new-m...ustangs/112150 I believe the intake deletes the need for charge motion plates which is where some of the horse power claim comes from. Not sure how they got 40 hp though.
2/8/07, 12:34 AM
#4
Member
Join Date: January 11, 2007
Posts: 4
Likes: 0
Received 0 Likes
on
0 Posts
They apparently just made 20+ horsepower, but the powerband was too high (ie. rpm needed for the additional power). They are going to redesign the intake runners for the next go. The 40hp was most likely done with a supercharged option.
2/8/07, 01:52 AM
#6
GT Member
Join Date: October 28, 2006
Location: CA
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
Alot of people around here were thinking that half the hp claim would come from throwing it on a stock motor and tuning it. (~10hp for removing the CMCVs and ~15 for tuning it) I still have hope though. N/A power is starting to get hard to come by.
2/8/07, 08:55 PM
#10
Shelby GT350 Member
Join Date: June 4, 2006
Location: McAllen, TX
Posts: 2,244
Likes: 0
Received 0 Likes
on
0 Posts
i thought Accufab was going to come out with something but i asked them back in 06 and they said it would be out soon and no word on anything since then (mind you this was in the begining of 06 around Feb or Mar)
2/8/07, 09:18 PM
#11
THE RED FLASH ------ Master-Moderator
Yes, your correrct C&L is working on a 3v intake manifold for the 05-07 Stang but there's no date set just yet.. it's still in the development stages right now
2/9/07, 08:29 PM
#13
Mach 1 Member
Join Date: August 31, 2006
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
If C&L can put together an aluminum high flow intake along the lines of the one I had from FRPP on my '96, I would buy it. The FRPP intake got me about 20-25 HP mostly above 4000 rpm. It worked very well.
2/9/07, 09:56 PM
#15
Legacy TMS Member
Boy, that's a tough one...... lol!
If that's true, then there will be another company that rhymes with Hedlecrock coming up with one soon..... I have a Performer RPM intake on my '92 that works really well.
If that's true, then there will be another company that rhymes with Hedlecrock coming up with one soon..... I have a Performer RPM intake on my '92 that works really well.
Thread
Thread Starter
Forum
Replies
Last Post