CDC Shaker!!!
6/28/07, 08:40 PM
#21
Legacy TMS Member
Join Date: May 24, 2006
Location: San Diego
Posts: 7,409
Likes: 0
Received 0 Likes
on
0 Posts
Congrats and welcome to the Shaker club.
Small suggestion if I may. Loosen the Throttle Body bolts slightly and push the shaker about 1/2" towards the driver side.
You can see in this pic that it's slightly to far to the passenger side.
Small suggestion if I may. Loosen the Throttle Body bolts slightly and push the shaker about 1/2" towards the driver side.
You can see in this pic that it's slightly to far to the passenger side.
6/28/07, 10:41 PM
#22
Shelby GT350 Member
Thread Starter
thanks man, i did notice the little bit more of a gap there, but i was hoping no one else would!!!!!
now i got to fix it so nobody notices.... or just not take any more photos straight on any more.... grrrrr
now i got to fix it so nobody notices.... or just not take any more photos straight on any more.... grrrrr
6/28/07, 11:10 PM
#24
Looks good Nate!
Like Leo said, welcome to the Shaker Club!
Like Leo said, welcome to the Shaker Club!
6/28/07, 11:16 PM
#26
Cobra Member
Join Date: March 3, 2007
Location: Eden Prairie, MN
Posts: 1,187
Likes: 0
Received 0 Likes
on
0 Posts
6/30/07, 10:59 AM
#29
Shelby GT350 Member
Thread Starter
i read in the online manual that it comes with a block off plate for the fender airbox opening..... mine did not come with this.
i also remember reading that the shaker does not allow enough air flow so the stock airbox opening needs to stay open....
what do you guys think? have any of you tried blocking the stock opening?
i also remember reading that the shaker does not allow enough air flow so the stock airbox opening needs to stay open....
what do you guys think? have any of you tried blocking the stock opening?
7/1/07, 04:06 PM
#31
Cobra Member
put that license plate on the rear!!!!!
if i had to have a mustang right now it would be one just liek yours but witha a blacked out hood, looks awesome man. wasnt it scary cutting that hole
if i had to have a mustang right now it would be one just liek yours but witha a blacked out hood, looks awesome man. wasnt it scary cutting that hole
7/1/07, 08:33 PM
#32
Mach 1 Member
Join Date: October 9, 2006
Posts: 517
Likes: 0
Received 0 Likes
on
0 Posts
yeh, I want one of those sooooooooooooo bad...My dad wont let me buy one though. He's really scared about cutting the hole, and that if I mess up he didnt want to have to drop some huge bill at the body shop that I couldnt afford....just to get it fixed. There is logic, but cOMONNNNNN THAT LOOKS SOOOOOOOO COOL!
7/1/07, 09:51 PM
#33
Shelby GT350 Member
Thread Starter
The hole was CAKE man....
i did it with an angle grinder!!!!
and it was still easy.... you tape it off, tape down the template, cut it out with a razer, then cut it out...
its aluminum too so it cuts like butter!!! no problem at all
i did it with an angle grinder!!!!
and it was still easy.... you tape it off, tape down the template, cut it out with a razer, then cut it out...
its aluminum too so it cuts like butter!!! no problem at all
7/2/07, 05:39 AM
#35
Bullitt Member
[quote=n8rfastback;951125]also, installing the bolts in the throttle body were a pain too...
We have found that if you cut the bottom of the holes on the trottle body mount, you can just slip it over the bolts and adjust it where you want it and tighten it down.
I also have one in stock, pm me for a TMS price.
We have found that if you cut the bottom of the holes on the trottle body mount, you can just slip it over the bolts and adjust it where you want it and tighten it down.
I also have one in stock, pm me for a TMS price.
8/23/07, 06:29 PM
#38
Cobra Member
Looking good Nate. How do you like that JLT?
Also, like Leo says, but the sill letters on your shaker.I had them on mine before I cut the shroud off, really added to it. Here's a pic before I trimmed the shroud.
Also, like Leo says, but the sill letters on your shaker.I had them on mine before I cut the shroud off, really added to it. Here's a pic before I trimmed the shroud.
