View Poll Results: Would you be interested in a set?

Don't care for those wheel.

24.44%

I would buy a set if they where available.

75.56%

Voters: 45. You may not vote on this poll

“19X11” HRE P40/V710/RTR STYLE WHEEL CONTENT INSIDE!!!!

Reply Subscribe

Thread Tools

Search this Thread

Oct 20, 2010 | 06:51 PM

#41

PIKE2244

Cobra Member

Joined: August 1, 2005

Posts: 1,329

Likes: 1

Hey george thank you for taking the time to explain that... You did a very good job and have to say that if you lose your day job you may want to look into teaching!!!! :-)

Oct 21, 2010 | 12:50 AM

#42

TTS197

Thread Starter

Mach 1 Member

Joined: November 3, 2007

Posts: 590

Likes: 0

From: South Florida

Quote:

Originally Posted by 2k7gtcs

Well I failed to realize until after I finished the post above was that when you widen a wheel you not only change the back spacing, but you are also changing the offset. You haven't done anything to machine it, but the centerline of a 11"'wheel width is moved inboard and the offset increases.

By my math my original wheel if widened to 11" would then have a 52mm offset
If widened to 11.5" they would have a 60mm offset

That's what makes it such a pain. 8, 9, 9.5, 10, 11 inch wheels all require different offsets for these cars.

If I have any clue what I'm talking about.

I'm 99% certain that Steeda uses a 52-53mm offset for their 20x11's, Maybe 908ssp would like to elaborate if this is correct since he has those wheels?

Oct 21, 2010 | 11:43 AM

#43

icemant180

Team Mustang Source

Joined: May 19, 2004

Posts: 964

Likes: 0

From: Bauhston

I like them, but as stated by Chris earlier in the thread, you are extremely limited on tire selection.

Oct 22, 2010 | 09:13 AM

#44

CO_VaporGT_09

Cobra Member

Joined: August 5, 2008

Posts: 1,369

Likes: 0

From: Arvada, CO

Quote:

Originally Posted by TTS197

I'm 99% certain that Steeda uses a 52-53mm offset for their 20x11's, Maybe 908ssp would like to elaborate if this is correct since he has those wheels?

Says here that they're 45 offset, don't know if that's accurate.

Wheel Stats
Wheel Height 20"
Wheel Width 9.5" or 11"
Finish Black w/ Machined Lip
Casting Low Pressure
Hub Bore 70.6 mm
Bolt Pattern 5 x 114.3 mm
Offset 45 mm

Label pic is fuzzy on this ebay listing, but seems like it says 59??

http://cgi.ebay.com/ebaymotors/2005-...ltDomainQ5f100

Last edited by CO_VaporGT_09; Oct 22, 2010 at 09:17 AM.

Oct 22, 2010 | 04:11 PM

#45

TTS197

Thread Starter

Mach 1 Member

Joined: November 3, 2007

Posts: 590

Likes: 0

From: South Florida

Quote:

Originally Posted by CO_VaporGT_09

Nice catch.

I believe the 45mm would be for the front wheels sounds like they are a bit conservative in the offset department for a 20x9.5 IMO. I’m thinking the reason for that it’s because not everyone is looking to run a staggered set, meaning that the wheels also have to fit the back of the vehicle with a good amount of room as well.

Sometime back I thought it was mentioned that the offset was in the low 50’s for the 20x11’s but for some reason I can’t find the thread. It does look like the boxes are marked with a 59mm as the offset. hmmmm

Last edited by TTS197; Oct 22, 2010 at 04:12 PM.

Nov 17, 2010 | 09:25 AM

#46

Digital_Synapse

June '11 MOTM Winner

Joined: April 11, 2007

Posts: 832

Likes: 2

From: Deep in the heart of TEXAS

I've proven my own assumptions. The 45 in 013-0021-45B - Steeda Spyder - Black w/ Machined Lip - 20x9.5, designates a 45mm offset, and the 59 in 013-0021-59B - Steeda Spyder - Black w/ Machined Lip - 20x11 means 59mm offset!!!! Spoke with several Steeda technicians for verification.