Going to dyno the cobra Saturday...
#1
Stubborn Bear
TMS Staff
TMS Staff
Thread Starter
Anyone wanna make any predictions?
Mods are:
Mac O/R H-Pipe
MIL eliminators from PEP
Magnaflow Mufflers (welded into stock catback)
C&L 80mm Mass Air Meter
C&L Trueflow inlet pipe
MSD 8.5mm Superconductor Wires
MSD Coil Packs
FRPP 4.10 gears
FRPP Aluminum Driveshaft
and
NOS Super Power Shot EFI Wet-kit (100shot)
Last time I dyno'd was without the C&L inlet pipe or MAF and made 275rwhp 272rwtq.
N/A I am hoping for at or over 280rwhp/tq.
On the Juice, I have no idea.
Mods are:
Mac O/R H-Pipe
MIL eliminators from PEP
Magnaflow Mufflers (welded into stock catback)
C&L 80mm Mass Air Meter
C&L Trueflow inlet pipe
MSD 8.5mm Superconductor Wires
MSD Coil Packs
FRPP 4.10 gears
FRPP Aluminum Driveshaft
and
NOS Super Power Shot EFI Wet-kit (100shot)
Last time I dyno'd was without the C&L inlet pipe or MAF and made 275rwhp 272rwtq.
N/A I am hoping for at or over 280rwhp/tq.
On the Juice, I have no idea.
#3
Stubborn Bear
TMS Staff
TMS Staff
Thread Starter
279rwhp, 277rwtq n/a.... a/f was off hte scale rich. 10.0 flat. I have at least 15rwhp in the car if i can get the a/f up.
On the spray, a/f going 10.0 again 350rwhp/383rwtq. Once I get the a/f in the 12.0:1 range, i should be around 390rwhp/440rwtq.
On the spray, a/f going 10.0 again 350rwhp/383rwtq. Once I get the a/f in the 12.0:1 range, i should be around 390rwhp/440rwtq.
#5
Scothew-
When do you plan on taking her (Very nice Cobra BTW) to the track and give her the "juice"? Are you going to wait until you get the a/f combo "just right"?
Also, Nice numbers!
When do you plan on taking her (Very nice Cobra BTW) to the track and give her the "juice"? Are you going to wait until you get the a/f combo "just right"?
Also, Nice numbers!
#6
Stubborn Bear
TMS Staff
TMS Staff
Thread Starter
The numbers are ok. I am planning on playing with a smalller fuel jet soon. May also try and get a different MAF and get it tuned. Not sure yet.
Track numbers will be soon, but I am also working on getting 2 15" wheels that will fit to mount my e/t drags on I dont think my 17" drag radials are going to hold that kinda trq down to well, heck they dont work good n/a.
Track numbers will be soon, but I am also working on getting 2 15" wheels that will fit to mount my e/t drags on I dont think my 17" drag radials are going to hold that kinda trq down to well, heck they dont work good n/a.
#8
Stubborn Bear
TMS Staff
TMS Staff
Thread Starter
well i have 7/16ths" spacers to run on the back which will let just about any 15" wheel clear. My issue now is stud-ength. I am going to HAVE to get some nice 3" studs before I can safely run them on the back with these spacers.
Thread
Thread Starter
Forum
Replies
Last Post