1964-1970 Mustang Member Tech & Restoration Discussion

Brenspeed Dyno Day

Thread Tools
 
Search this Thread
 
Old May 5, 2007 | 12:31 PM
  #1  
codeman94's Avatar
Thread Starter
 
Joined: December 14, 2004
Posts: 7,933
Likes: 16
From: Goshen, IN
Brenspeed Dyno Day

Welp...I finally got my car on a dyno after owning her for over 5 years. A couple of the S197 guys were getting together for the thing, and I didn’t live too far away so I figured I'd take the opportunity to test the car! Lots of cool cars there and it was great to meet the guys! The results were little disappointing, but there are a couple of silver linings.

On my best pull:

157.49 RWHP
217.91 RWTQ



Weather conditions: 73.33 Degrees F, Barometric Pressure: 29.33, Humidity: 29%

HOWEVER....the guys at the shop said that I needed to have my timing adjusted badly because my curve was so flat. I peaked at 3750 RPM and it never fell off. He said that I have a good 15 more rwhp in there waiting to be unlocked if everything was timed up well. ANOTHER silver lining is that my car really performs well on the street....(probably because it only weighs ~2300lbs)...so anything that makes an improvement in my performance numbers will be greatly amplified on the street!

I'll get my prinout scanned and posted as soon as I can.

Oh....and as far as I know, I won the "lowest hp of the day" award...a duster...consolation prizes always make you feel better.
Reply
Old May 5, 2007 | 12:35 PM
  #2  
jaiasmit's Avatar
GT Member
 
Joined: August 15, 2006
Posts: 102
Likes: 0
It was good to meet you today codeman. The car sounds and looks great. It may not make the best numbers, but it's still a nice car.

Glad to hear you made it back to SB OK. Hope to run into you again some time soon.
Reply
Old May 5, 2007 | 06:21 PM
  #3  
tom281's Avatar
Legacy TMS Member
 
Joined: October 8, 2005
Posts: 12,395
Likes: 29
From: Medina county, OH
Your car looks good, sounds good, makes decent power, and is a nice street machine... you should be proud man!
Reply
Old May 7, 2007 | 02:28 PM
  #4  
codeman94's Avatar
Thread Starter
 
Joined: December 14, 2004
Posts: 7,933
Likes: 16
From: Goshen, IN
here is the curve...I like the flatness...just wish it was about 150 horsepower higher!
Attached Thumbnails Brenspeed Dyno Day-dyno-sheet-5-5-07.jpg  
Reply
Old May 7, 2007 | 04:43 PM
  #5  
future9er24's Avatar
Post *****
 
Joined: May 13, 2004
Posts: 18,616
Likes: 3
From: Berkeley/Redwood City, CA
That's not to bad. 196.8hp and 272.4tq at the flywheel. Get it timed and such you'll be past the 200hp mark giving you less than 11.5lb/hp, which isnt a bad number to have!
Reply
Old May 8, 2007 | 03:35 PM
  #6  
codeman94's Avatar
Thread Starter
 
Joined: December 14, 2004
Posts: 7,933
Likes: 16
From: Goshen, IN
I think I'm looking pretty good...I looked for some numbesr on other engines, and I found this build....and I make more power than this motor.

Reply
Old May 9, 2007 | 09:36 PM
  #7  
codeman94's Avatar
Thread Starter
 
Joined: December 14, 2004
Posts: 7,933
Likes: 16
From: Goshen, IN
here are some pics....sorry some are fuzzy....the guy in the purple shirt is me.
Attached Thumbnails Brenspeed Dyno Day-wrenched.jpg   Brenspeed Dyno Day-wrenched-2.jpg   Brenspeed Dyno Day-twins.jpg  
Reply
Old May 10, 2007 | 06:06 PM
  #8  
future9er24's Avatar
Post *****
 
Joined: May 13, 2004
Posts: 18,616
Likes: 3
From: Berkeley/Redwood City, CA
Hadn't seen those new tires until now, gotta say they don't look as bad as you said they did
Reply
Old May 10, 2007 | 06:17 PM
  #9  
codeman94's Avatar
Thread Starter
 
Joined: December 14, 2004
Posts: 7,933
Likes: 16
From: Goshen, IN
oh yeah...I forgot about that!....I've warmed up to them. They are a bit taller, but I like the look.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Road_Runner
5.0L GT Modifications
67
Sep 2, 2024 04:46 PM
NC14GT
Road Trips
43
Sep 10, 2017 04:47 PM
FordOfMurfreesboro
Introductions
0
Sep 29, 2015 02:19 PM
JTB
Motorsports
1
Sep 3, 2015 10:50 AM




All times are GMT -6. The time now is 09:11 AM.