New DIB owner
#61
Bullitt Member
Thread Starter
#63
Bullitt Member
Thread Starter
Couple of pics with the 18% tint. Next summer will be back in the US somewhere and get the other windows tinted
Before
After
Before
After
Last edited by SSStang; 5/25/14 at 05:55 AM.
#64
Bullitt Member
Thread Starter
Put the new rear shocks on. Just need to change the front struts next week after I get it back from the body shop
Last edited by SSStang; 6/17/14 at 07:37 AM.
#65
Shelby GT500 Member
Nice. I am saving for the KW ClubSport coilovers so I can have the most adjustability I can get. Eventually I will spend a lot of time on the track. Next year I hope to get in at least 50 laps at the Ring too.
#66
Bullitt Member
#67
Bullitt Member
Thread Starter
I can't wait to get the front done.
#68
Bullitt Member
Thread Starter
Well I got this from emblem pros today. I should get the car back from the shop friday so it will have to wait to go on.
Last edited by SSStang; 5/27/14 at 12:39 PM.
#69
Bullitt Member
Thread Starter
Got car back from the shop the other day so no more messed up bumper. Still have issues with paint and mufflers but o well.
Went out the Bitburg for some drag racing yesterday with some other mustang from K-town. I had a great time.
Here is my best run.
Went out the Bitburg for some drag racing yesterday with some other mustang from K-town. I had a great time.
Here is my best run.
#71
Bullitt Member
Thread Starter
#75
Bullitt Member
Thread Starter
#76
Bullitt Member
Thread Starter
http://youtu.be/7KEUQksMUjUOk So I went back to Bitburg for another day 1/4 mile fun. Here are some pic and a vid. It was better this time not crowded at all and was able to make runs with a very short wait. I didn't really improve my time. So that airaid didn't give me anything but o well it will help when I get a tune.
The VR12 engine in back and front.
The VR12 engine in back and front.
Last edited by SSStang; 6/24/14 at 03:59 AM.
#77
Bullitt Member
Thread Starter
Here is the vid
http://youtu.be/7KEUQksMUjU
http://youtu.be/7KEUQksMUjU
Last edited by SSStang; 6/24/14 at 04:01 AM.
#78
Bullitt Member
Thread Starter
Finally installed my BMR UCA and bracket. Install was not to bad and didn't notice any more noise. I think majority of the rear end noise came from installing the LCA.
Also got a SCT x4 from steeda and picked up a used set of jegs cat deletes. Car is defiantly louder and picked up some HP! Just might be to loud gonna give it a few weeks and see. It took some messing with adjusting and adjusting to get the cat deletes to seal good.
Also got a SCT x4 from steeda and picked up a used set of jegs cat deletes. Car is defiantly louder and picked up some HP! Just might be to loud gonna give it a few weeks and see. It took some messing with adjusting and adjusting to get the cat deletes to seal good.
#80
Bullitt Member
Thread Starter
Since the car is parked for winter I have been messing with some stuff. Removed the fog lights and replacing with mesh. Only did one side yesterday. might let some more air under the hood.
I also pulled the front struts to swap in the Koni orange I have had for a while now. Now gotta take them the hobby shop to use spring compressor.
I also pulled the front struts to swap in the Koni orange I have had for a while now. Now gotta take them the hobby shop to use spring compressor.