Looks like we are getting the SVT mufflers stock
#1
Thread Starter
Looks like we are getting the SVT mufflers stock
Am I right?
#2
Join Date: December 3, 2007
Location: Orlando, Florida
Posts: 713
Likes: 0
Received 0 Likes
on
0 Posts
Looks like it. At least the four inch tips. Maybe the chambering is different?
#3
I saw some close up pics of the exhaust. Can't remember if it was taken from someone at a car show or a press release pic but it looked like the tips were 4" BUT only for decoration. You could see the actual exhaust further inside and it was a bit smaller. Didn't look too great but at least with the baffles out of the side exhausts it should be a good sounding system. I'm crossing my fingers.
Last edited by Bones Applesauce; 12/10/10 at 06:02 PM.
#5
FR500 Member
Join Date: July 1, 2008
Location: Oxford, UK
Posts: 3,336
Likes: 0
Received 0 Likes
on
0 Posts
I saw some close up picks of the exhaust. Can't remember if it was taken from someone at a car show or a press release pick put it looked like the tips were 4" BUT only for decoration. You could see the actual exhaust further inside and it was a bit smaller. Didn't look too great but at least with the baffles out of the side exhausts it should be a good sounding system. I'm crossing my fingers.
#6
GT Member
Join Date: August 26, 2010
Location: Fort Worth, Texas
Posts: 145
Likes: 0
Received 0 Likes
on
0 Posts
I'm planning on installing electric dump valves, but the stock discs look to be 2 bolt and everything I have been able to find on the market is 3 bolt. Does anyone know of a manufacturer making a 2 bolt or am I going to have to ge new flanges welded on?
#7
Member
Join Date: December 10, 2010
Location: Motor City, USA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
#8
Member
Join Date: December 10, 2010
Location: Motor City, USA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
#9
Thread Starter
I am dumb.
Last edited by 06GT; 12/10/10 at 04:01 PM.
#10
Bullitt Member
#11
Mach 1 Member
Join Date: October 29, 2010
Location: Florida
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
#12
Mach 1 Member
Join Date: October 29, 2010
Location: Florida
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
and these vids were without the diffuser discs? Also if so, were there dump valves installed or were just the discs removed and remainder of system stock?
PM if you wish...
#13
Thread Starter
#14
Thread Starter
#16
AKA 1 BULLITT------------ Legacy TMS Member
#17
Mach 1 Member
Join Date: October 29, 2010
Location: Florida
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
As stated...same as GT's just different tips. BTW check the vids that S197 has on youtube...obviously VERY close to the Boss or S197 development program, or has a CLOSE friendship with the Ford development engineers
#19
Member
Join Date: December 10, 2010
Location: Motor City, USA
Posts: 43
Likes: 0
Received 0 Likes
on
0 Posts
Those are pre-production (incorrect) parts shown in the picture. The production tip is similar to the 2011 GT automatic with a 4" tip welded over the 2.5" outlet pipe (for appearance). To meet exterior noise requirements, tailpipe sound has to be slightly reduced to allow room for the additional sound that comes from the sidepipes. That's why the big, full-size 4" tip is not used in production on the Boss. Hope this clears it up.
#20
Tasca Super Boss 429 Member
Join Date: December 18, 2010
Location: NorCal
Posts: 3,708
Likes: 0
Received 0 Likes
on
0 Posts
Those are pre-production (incorrect) parts shown in the picture. The production tip is similar to the 2011 GT automatic with a 4" tip welded over the 2.5" outlet pipe (for appearance). To meet exterior noise requirements, tailpipe sound has to be slightly reduced to allow room for the additional sound that comes from the sidepipes. That's why the big, full-size 4" tip is not used in production on the Boss. Hope this clears it up.