Shaker 500 - What should I tap into for LOC?
#1
Shaker 500 - What should I tap into for LOC?
I have the Shaker 500 and will be installing the JL Audio Stealthbox and Alpine PDX-M6 mono amp. I also purchased a LC2i line out converter (LOC) because I do not want to replace the factory head unit. The tech at Crutchfield stated I should tap into the rear deck speakers at either the Shaker amp output (located above driver kickpanel) or at the rear speakers themselves...it does not matter. He stated the rear speakers produce a good range and the Alpine amp would filter for the lows. From reading other forums, it sounds like the rear speakers are not good to tap into because they are plain ol' crap.
Does anyone have a definitive answer with good reasoning on what should be tapped into...the rear speakers, the subs in the doors, or the door speakers?
Does anyone have a definitive answer with good reasoning on what should be tapped into...the rear speakers, the subs in the doors, or the door speakers?
#2
Cobra R Member
Join Date: September 22, 2012
Location: Ontario, California
Posts: 1,691
Likes: 0
Received 17 Likes
on
17 Posts
I have the Shaker 500 and will be installing the JL Audio Stealthbox and Alpine PDX-M6 mono amp. I also purchased a LC2i line out converter (LOC) because I do not want to replace the factory head unit. The tech at Crutchfield stated I should tap into the rear deck speakers at either the Shaker amp output (located above driver kickpanel) or at the rear speakers themselves...it does not matter. He stated the rear speakers produce a good range and the Alpine amp would filter for the lows. From reading other forums, it sounds like the rear speakers are not good to tap into because they are plain ol' crap.
Does anyone have a definitive answer with good reasoning on what should be tapped into...the rear speakers, the subs in the doors, or the door speakers?
Does anyone have a definitive answer with good reasoning on what should be tapped into...the rear speakers, the subs in the doors, or the door speakers?
#3
V6 Member
Join Date: October 16, 2012
Location: Nebraska
Posts: 51
Likes: 0
Received 0 Likes
on
0 Posts
Yep, you can use the rear speakers which will probably be the easiest to get at anyway.
Let us know how this works for you. I have the stealthbox in my 2013, but i went with a 5-channel that has a 300-Watt RMS Mono output going to the stealth box. With some music, i feel that it is enough to the sub, but then with other styles i feel that it needs to be louder. So i am debating daisy chaining a dedicated Class D amp for it, or just swapping it out for a more powerful 5 channel, or leaving it as is.
Let us know how this works for you. I have the stealthbox in my 2013, but i went with a 5-channel that has a 300-Watt RMS Mono output going to the stealth box. With some music, i feel that it is enough to the sub, but then with other styles i feel that it needs to be louder. So i am debating daisy chaining a dedicated Class D amp for it, or just swapping it out for a more powerful 5 channel, or leaving it as is.
#4
Legacy TMS Member
Yep, you can use the rear speakers which will probably be the easiest to get at anyway.
Let us know how this works for you. I have the stealthbox in my 2013, but i went with a 5-channel that has a 300-Watt RMS Mono output going to the stealth box. With some music, i feel that it is enough to the sub, but then with other styles i feel that it needs to be louder. So i am debating daisy chaining a dedicated Class D amp for it, or just swapping it out for a more powerful 5 channel, or leaving it as is.
Let us know how this works for you. I have the stealthbox in my 2013, but i went with a 5-channel that has a 300-Watt RMS Mono output going to the stealth box. With some music, i feel that it is enough to the sub, but then with other styles i feel that it needs to be louder. So i am debating daisy chaining a dedicated Class D amp for it, or just swapping it out for a more powerful 5 channel, or leaving it as is.
What amp do you have? Also, what speakers/ what is the rest of the system?
#5
Member
Join Date: August 16, 2012
Location: Southeast Michigan
Posts: 6
Likes: 0
Received 0 Likes
on
0 Posts
I know this might be a bit late, but if you have a shaker radio, you can tap right into the pre-amp output on the head unit. It's connector C290B and it has all the pins you need. Enable , + , - , and Shield. There is one set for front (shaker 500) and one set for rear (shaker 1000). 8 pins total.
Did this on my sub install and it works beautiful. Clean wiring (no LOC) and the amp isn't running unless my radio is on.
(go to page 3 of 13)
http://iihs.net/fsm/?dir=710&viewfil...Navigation.pdf
Did this on my sub install and it works beautiful. Clean wiring (no LOC) and the amp isn't running unless my radio is on.
(go to page 3 of 13)
http://iihs.net/fsm/?dir=710&viewfil...Navigation.pdf
#6
So no bass roll off? I want a clean install and don't want to buy a LOC if I don't need to. The other threads all complain of roll off though. I know my way around electronics and like a good clear sound, but I'm no audiophile. Just want some more bass.
And dumb question of the day...where do the rear speakers hook up in the diagram?
Thanks!
And dumb question of the day...where do the rear speakers hook up in the diagram?
Thanks!
Last edited by 12GTCS; 2/25/13 at 12:30 PM.
#7
Mach 1 Member
Join Date: January 25, 2011
Location: Ville Platte, Louisiana
Posts: 1,075
Likes: 0
Received 1 Like
on
1 Post
If I could make a suggestion. PAC AOEM-FRD24. I use this in my car. No tapping any wires. You just plug into the back of the radio, then plug the harness into the other end. NO tapping or cutting any wires and you get front and rear RCA's. Unless you are going with an active LOC like the AudioControl devices that eliminate bass roll off that's how I did it and it works well for me. I got mine for like $34 on Ebay.
#8
Mach 1 Member
Join Date: January 25, 2011
Location: Ville Platte, Louisiana
Posts: 1,075
Likes: 0
Received 1 Like
on
1 Post
Oh and for the roll off issue I use a Bass Epicenter made by Soundstream. It works well but aftermarket head units still have a better bass range. I haven't used any of the AudioControl units so I have nothing to compare it to except stock but it is way better than stock.
#9
Finally got mine installed. Pioneer 12" SVC running 400W RMS. More bass than I'll ever need and it sounds great. Thanks for the tips guys! Thanks to evil cart man as well his walkthrough had some great pictures and explanations.
Last edited by 12GTCS; 4/20/13 at 09:47 PM.
#10
If I could make a suggestion. PAC AOEM-FRD24 . I use this in my car. No tapping any wires. You just plug into the back of the radio, then plug the harness into the other end. NO tapping or cutting any wires and you get front and rear RCA's. Unless you are going with an active LOC like the AudioControl devices that eliminate bass roll off that's how I did it and it works well for me. I got mine for like $34 on Ebay.
Thats great advice , any idea if the PAC AOEM-FRD24 will be compatible with my 2013 mustang . I checked on ebay and but seems like its only compatible with 05-10 mustangs
Last edited by gt5.Oh; 7/13/16 at 01:27 PM.
Thread
Thread Starter
Forum
Replies
Last Post
Steve@CJPP
Vendor Showcase
1
9/15/15 06:20 AM