Where is the oil pressure sending unit?
#1
9 is not my lucky number.
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Thread Starter
I have an oil pressure gauge I want to mount but have no idea where to tap into. People have been vauge and said it's down by the oil filter, which isn't helpful. Can somebody post a pic or describe in detail where it goes? Thanks.
I assume I would tee into the stock sending unit port with brass NPT fittings.
I assume I would tee into the stock sending unit port with brass NPT fittings.
#2
Team Mustang Source
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Yeah that's where it is
It's screwed into a bung near the filter and looks like this pic. There's a single wire coming out of it, a gray one. Mine is out of the car because the thing is useless. It's not a pressure sending unit at all, it's a switch that reads fat dumb and happy at anything above 5 or 6 psi - nice eh? I grounded the wire to keep the "gauge" on the dash happy. In the spot where it was, I put a braided steel line that goes to the real pressure sending unit (Autometer) that's mounted to the back side of the JLT heat shield.
![Wink](https://themustangsource.com/forums/images/smilies/wink.gif)
#3
9 is not my lucky number.
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Thread Starter
What does that screw into? Right into the lower block? The oil pan?
Why did you run the steel line? I saw that post. Why didn't you just put the sending unit down there?
Why did you run the steel line? I saw that post. Why didn't you just put the sending unit down there?
#4
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Join Date: December 18, 2004
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Screws into the block that houses the lower radiator hose, oil filter and that little thing you see above, drivers side of the block at the front. I know this pic doesn't show it but it is on the opposite side of the oil filter.
#5
Team Mustang Source
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Originally posted by dustindu4@January 31, 2006, 8:31 PM
What does that screw into? Right into the lower block? The oil pan?
Why did you run the steel line? I saw that post. Why didn't you just put the sending unit down there?
What does that screw into? Right into the lower block? The oil pan?
Why did you run the steel line? I saw that post. Why didn't you just put the sending unit down there?
![Wink](https://themustangsource.com/forums/images/smilies/wink.gif)
This pic shows exactly where the braided steel line is threaded into where the factory switch used to be. If you shine a flashlight at the driver's side header and look just behind the oil filter, you should see the switch (sending unit
![Icon Rolleyes](https://themustangsource.com/forums/images/smilies/icon_rolleyes.gif)
I used a braided steel line because I don't trust the plastic capillary tubing and compression fittings. Not sure about other manufacturer's sending units, but the Autometer unit is just a hair too big to fit into the factory spot. I mean it's dang close - so close that you could probably fit it in there and cross-thread it in the process and end up with a whole new world of troubles
![Wink](https://themustangsource.com/forums/images/smilies/wink.gif)
#7
9 is not my lucky number.
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Thread Starter
That picture is really helpful, thanks. Yeah that port looks really tight, good idea on the braided hose. You really don't want to muck up the threads in the aluminum block, that would be bad. Question though, does the oil actually make it all the way up that hose or are you reading air pressure?
BTW thanks for taking the time to go out and take pictures, I appreciate it.
What is the thread size that goes into the block is it 1/4" NPT?
BTW thanks for taking the time to go out and take pictures, I appreciate it.
What is the thread size that goes into the block is it 1/4" NPT?
#8
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Join Date: December 18, 2004
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Oil will feed all the way up the line, and plenty of it, make sure you ground your sending unit somehow or it won't read properly. This is actually the access for the oil feed line for the turbo system we are installing, we have a T off of it for both the factory sending unit and an Auto Meter sender.
BTW, if you mess up the threads you won't have destroyed the block, it actually is a removable unit from off of the block and can be replaced.
BTW, if you mess up the threads you won't have destroyed the block, it actually is a removable unit from off of the block and can be replaced.
![04](https://themustangsource.com/forums/images/smilies/04.gif)
#10
Team Mustang Source
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Originally posted by dhof303@January 31, 2006, 9:20 PM
Oil will feed all the way up the line, and plenty of it, make sure you ground your sending unit somehow or it won't read properly. This is actually the access for the oil feed line for the turbo system we are installing, we have a T off of it for both the factory sending unit and an Auto Meter sender.
BTW, if you mess up the threads you won't have destroyed the block, it actually is a removable unit from off of the block and can be replaced.![04](https://themustangsource.com/forums/images/smilies/04.gif)
Oil will feed all the way up the line, and plenty of it, make sure you ground your sending unit somehow or it won't read properly. This is actually the access for the oil feed line for the turbo system we are installing, we have a T off of it for both the factory sending unit and an Auto Meter sender.
BTW, if you mess up the threads you won't have destroyed the block, it actually is a removable unit from off of the block and can be replaced.
![04](https://themustangsource.com/forums/images/smilies/04.gif)
#11
Team Mustang Source
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Originally posted by dustindu4@January 31, 2006, 9:17 PM
That picture is really helpful, thanks. Yeah that port looks really tight, good idea on the braided hose. You really don't want to muck up the threads in the aluminum block, that would be bad. Question though, does the oil actually make it all the way up that hose or are you reading air pressure?
BTW thanks for taking the time to go out and take pictures, I appreciate it.
What is the thread size that goes into the block is it 1/4" NPT?
That picture is really helpful, thanks. Yeah that port looks really tight, good idea on the braided hose. You really don't want to muck up the threads in the aluminum block, that would be bad. Question though, does the oil actually make it all the way up that hose or are you reading air pressure?
BTW thanks for taking the time to go out and take pictures, I appreciate it.
What is the thread size that goes into the block is it 1/4" NPT?
![Thumb](https://themustangsource.com/forums/images/smilies/thumb.gif)
#12
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Join Date: December 18, 2004
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
I don't know just yet, I still have mine "rigged" by wrapping a large hose clamp around it and attaching it to a couple of holes on the driver's side inner fender, of course I have a section of #6 AN steel braided line up to that area. I will have to rework the plumbing to make the #3 AN feed line to the turbo work. Then again I might just use the #6 to feed the turbo. The more oil flow the better, right? :scratch:
#13
9 is not my lucky number.
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Thread Starter
Originally posted by MTAS@January 31, 2006, 9:47 PM
Grounding the Autometer unit is something I did not do - any tips on where to put the wire on the unit?
Grounding the Autometer unit is something I did not do - any tips on where to put the wire on the unit?
#14
9 is not my lucky number.
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Thread Starter
Originally posted by dhof303@January 31, 2006, 9:51 PM
I don't know just yet, I still have mine "rigged" by wrapping a large hose clamp around it and attaching it to a couple of holes on the driver's side inner fender, of course I have a section of #6 AN steel braided line up to that area. I will have to rework the plumbing to make the #3 AN feed line to the turbo work. Then again I might just use the #6 to feed the turbo. The more oil flow the better, right? :scratch:
I don't know just yet, I still have mine "rigged" by wrapping a large hose clamp around it and attaching it to a couple of holes on the driver's side inner fender, of course I have a section of #6 AN steel braided line up to that area. I will have to rework the plumbing to make the #3 AN feed line to the turbo work. Then again I might just use the #6 to feed the turbo. The more oil flow the better, right? :scratch:
![Dunno](https://themustangsource.com/forums/images/smilies/dunno.gif)
#15
9 is not my lucky number.
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Thread Starter
Originally posted by MTAS@January 31, 2006, 9:50 PM
I only hope I can simply pass along what I've learned![Thumb](https://themustangsource.com/forums/images/smilies/thumb.gif)
I only hope I can simply pass along what I've learned
![Thumb](https://themustangsource.com/forums/images/smilies/thumb.gif)
#16
Team Mustang Source
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
Originally posted by dustindu4@January 31, 2006, 9:57 PM
Just make sure the body of the sending unit is touching something metal, which is touching the body. Then again, doesn't it get grounded with the stainless hose that feeds it?
Just make sure the body of the sending unit is touching something metal, which is touching the body. Then again, doesn't it get grounded with the stainless hose that feeds it?
![Doh](https://themustangsource.com/forums/images/smilies/doh.gif)
![04](https://themustangsource.com/forums/images/smilies/04.gif)
#17
Hey MTAS what do you mean you grounded the stock sending unit wire? Did this keep you from getting the low oil pressure warning? Does the stock needle stay flat or move to a normal position when grounded.
I tee'ed the stock fitting and am currently running the stock sending unit and the Autometer unit. But every once inwhile the stock needle comes about a 1/4 way up and then goes back down and I get the low oil pressure warning. The Autometer gauge is reading just fine so I'm not sure what the deal is. After reading this I'm thinking maybe it's because the stock unit isn't grounded it's just hanging off the brass tee and if I can just ground the wire instead of using the stock sending unit then I'd rather just do that for a cleaner install.
Jason
I tee'ed the stock fitting and am currently running the stock sending unit and the Autometer unit. But every once inwhile the stock needle comes about a 1/4 way up and then goes back down and I get the low oil pressure warning. The Autometer gauge is reading just fine so I'm not sure what the deal is. After reading this I'm thinking maybe it's because the stock unit isn't grounded it's just hanging off the brass tee and if I can just ground the wire instead of using the stock sending unit then I'd rather just do that for a cleaner install.
Jason
#20
Team Mustang Source
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
![](https://themustangsource.com/forums/images/rank.gif)
<div class='quotetop'>QUOTE(jskwarek @ February 1, 2006, 7:14 PM) Quoted post</div><div class='quotemain'>
Hey MTAS what do you mean you grounded the stock sending unit wire? Did this keep you from getting the low oil pressure warning? Does the stock needle stay flat or move to a normal position when grounded.
I tee'ed the stock fitting and am currently running the stock sending unit and the Autometer unit. But every once inwhile the stock needle comes about a 1/4 way up and then goes back down and I get the low oil pressure warning. The Autometer gauge is reading just fine so I'm not sure what the deal is. After reading this I'm thinking maybe it's because the stock unit isn't grounded it's just hanging off the brass tee and if I can just ground the wire instead of using the stock sending unit then I'd rather just do that for a cleaner install.
Jason
[/b][/quote]
I cut the wire going to the stock sending unit, extended it and grounded it (to a spot under the air filter if memory serves) to keep the gauge happy. It now looks no different than if it were still connected. I've had it this way and have never seen the needle move, just like when it was connected to the sending unit [img]style_emoticons/<#EMO_DIR#>/wink.gif[/img]
<div class='quotetop'>QUOTE(RRRoamer @ February 1, 2006, 7:35 PM) Quoted post</div><div class='quotemain'>
So is there anyway to replace the bloody switch with a proper sender to get oil pressure to the dash (vs. the yes/no junk from the switch)?
[/b][/quote]
Years ago it was possible to put a resistor or something like that on the back of the factory gauge, but I don't think that's possible now. Not only is it a switch on the one end, but the gauge itself is severely dampened. So even if you could get it to work, it wouldn't have the reaction time a real OP gauge does.
Hey MTAS what do you mean you grounded the stock sending unit wire? Did this keep you from getting the low oil pressure warning? Does the stock needle stay flat or move to a normal position when grounded.
I tee'ed the stock fitting and am currently running the stock sending unit and the Autometer unit. But every once inwhile the stock needle comes about a 1/4 way up and then goes back down and I get the low oil pressure warning. The Autometer gauge is reading just fine so I'm not sure what the deal is. After reading this I'm thinking maybe it's because the stock unit isn't grounded it's just hanging off the brass tee and if I can just ground the wire instead of using the stock sending unit then I'd rather just do that for a cleaner install.
Jason
[/b][/quote]
I cut the wire going to the stock sending unit, extended it and grounded it (to a spot under the air filter if memory serves) to keep the gauge happy. It now looks no different than if it were still connected. I've had it this way and have never seen the needle move, just like when it was connected to the sending unit [img]style_emoticons/<#EMO_DIR#>/wink.gif[/img]
<div class='quotetop'>QUOTE(RRRoamer @ February 1, 2006, 7:35 PM) Quoted post</div><div class='quotemain'>
So is there anyway to replace the bloody switch with a proper sender to get oil pressure to the dash (vs. the yes/no junk from the switch)?
[/b][/quote]
Years ago it was possible to put a resistor or something like that on the back of the factory gauge, but I don't think that's possible now. Not only is it a switch on the one end, but the gauge itself is severely dampened. So even if you could get it to work, it wouldn't have the reaction time a real OP gauge does.