GT Performance Mods 2005+ Mustang GT Performance and Technical Information

Pypes violators brand new 250 shipped

Thread Tools
 
Search this Thread
 
Old Jul 17, 2013 | 04:24 PM
  #1  
Glenn's Avatar
Thread Starter
Legacy TMS Member
 
Joined: August 7, 2006
Posts: 16,113
Likes: 789
From: In Boredom
Pypes violators brand new 250 shipped

Amazon.com: Pypes Exhaust SFM60V Violator 2-1/2" Diameter 4" Tips Stainless Steel Axle-Back Exhaust System for Ford Mustang Kit: Automotive Amazon.com: Pypes Exhaust SFM60V Violator 2-1/2" Diameter 4" Tips Stainless Steel Axle-Back Exhaust System for Ford Mustang Kit: Automotive

Thought it was a good enough price to pass it along.
Reply
Old Jul 18, 2013 | 05:55 PM
  #2  
Glenn's Avatar
Thread Starter
Legacy TMS Member
 
Joined: August 7, 2006
Posts: 16,113
Likes: 789
From: In Boredom
mine were just delivered... man that was fast shipping. Ordered at 345 on wed they shipped out the same day and they were dropped off around 5pm today
Reply
Old Sep 15, 2013 | 10:27 PM
  #3  
Gigantor's Avatar
Bullitt Member
 
Joined: March 14, 2013
Posts: 209
Likes: 9
From: BX, NY
Glenn, you told us they were delivered but no mention on how the install went or how they sounded afterwards.

I was looking at them on Amazon and the lowest I found was 238 and on ebay they were 250 from Yates Performance. I made them an offer of 230 and they accepted. It was a great deal and I received them very quickly.

Now onto the install... The driver side went on without a problem. The passenger side is a different story. The tip hung about 2" too low and it was up against the cut out of the bumper. Whoevers turn it was to install the hangers must have been hung over. Instead of sending it back I decided to heat the hanger until cherry red and straighten and re-bend them to where they will match the other side. OK about 1/2 hour later they were now both installed. The clamps they provide were found to be lacking. They didn't clamp on hard enough so the pipes had some wiggle in them.

All in all they are great for $230 shipped to my door. The sound is louder than stock but not excessive and the droning is acceptable. Much less than my SLP Loud Mouths.
Reply
Old Sep 16, 2013 | 06:20 AM
  #4  
Glenn's Avatar
Thread Starter
Legacy TMS Member
 
Joined: August 7, 2006
Posts: 16,113
Likes: 789
From: In Boredom
My install went well. The clamps needed to be tightened up more than I thought they would need to be. They didn't seem to be tightening correctly. Any way I lined everything up then tightened everything up. No alignment problems. Sound it right on the money as far as I am concerned. Step on it and you can hear them pretty well and cruising sound is very tolerable.
Reply
Old Sep 18, 2013 | 04:14 PM
  #5  
metroplex's Avatar
Legacy TMS Member
 
Joined: October 2, 2006
Posts: 4,777
Likes: 16
From: Southeast Michigan
I had to heat and bend one of the hangers. It seems I had to do that on my FR500S mufflers as well.
Reply
Old Sep 18, 2013 | 05:05 PM
  #6  
Glenn's Avatar
Thread Starter
Legacy TMS Member
 
Joined: August 7, 2006
Posts: 16,113
Likes: 789
From: In Boredom
did you have the mid pipes loose while you were trying to line things up??
Reply
Old Sep 18, 2013 | 05:27 PM
  #7  
metroplex's Avatar
Legacy TMS Member
 
Joined: October 2, 2006
Posts: 4,777
Likes: 16
From: Southeast Michigan
Yep! I tried aligning them every which way I could, but one tip was always pressed up against the bumper cover so I had to bend one of the axle back hangers. I had to do this on one of my FR500S mufflers as well.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
carid
Vendor Showcase
6
Mar 30, 2021 09:29 AM
MustangConvert11
'10-14 V6 Modifications
2
Sep 30, 2015 08:01 PM
PonyMuscletang13
2010-2014 Mustang
4
Sep 29, 2015 09:40 AM




All times are GMT -6. The time now is 01:18 PM.