MGW Shifter Feedback Thread!
#602
#604
George, historically your pictures never do the thing justice. It is based on this fact alone that I will be ordering one. It will be a tossup though between yours and grabberpony.com's Grabber Orange ball. I may swap them out according to my mood.
#605
oh and we also have a new shift ball and shaft coming out soon too
this is the ball ...the shaft will be finished this weekend!!!!
regards
george
#608
http://www.mgwltd.com/mustang_gripper_shift_knob.shtml
http://www.mgwltd.com/mustang_race_knob.shtml
regards
george
#609
thanks george...i've waited to get a shift **** because i wanted your mgw logo ****, since i have your 5-speed shifter installed..i don't recall the thread on it, but i have the original **** that came with my 95 gt stang, if that helps.... 12mm?
we will be making the ball with several threads and we have a few shift ***** for your car specifically. go here...
http://www.mgwltd.com/mustang_gripper_shift_knob.shtml
http://www.mgwltd.com/mustang_race_knob.shtml
regards
george
http://www.mgwltd.com/mustang_gripper_shift_knob.shtml
http://www.mgwltd.com/mustang_race_knob.shtml
regards
george
#610
V6 Member
Join Date: March 18, 2007
Location: Rhode Island
Posts: 69
Likes: 0
Received 0 Likes
on
0 Posts
The MGW shifter was installed without a hitch in my PJ yesterday. Used a very short throw setting and moved the shifter as close to the driver as possible and an inch higher than the original.
Had only one problem but it had nothing to do with the shifter. Whoever loctited the PJ shift **** on the shaft wanted it never to come off. Took us about 40 minutes to get if off trying a variety of methods.
The MGW is a must mod at least of a PJ, shifting up or down is now crisp, fast and a pleasure. A+ to MGW.
Had only one problem but it had nothing to do with the shifter. Whoever loctited the PJ shift **** on the shaft wanted it never to come off. Took us about 40 minutes to get if off trying a variety of methods.
The MGW is a must mod at least of a PJ, shifting up or down is now crisp, fast and a pleasure. A+ to MGW.
#611
Shelby GT350 Member
George , I really like that race handle in the second link for 1995's. Are you going to make one like that for us or a handle for our shifter that has the 1.75mm threads so we can use that one ...
#612
yes we are!!!
give me about 2 weeks to make some new handles for that thread.
regards
george
#614
Team Mustang Source Legacy Member
I had the same problem with the shift **** shaft spinning, did the same thing, messed around with the **** itself for a while until I figured out it was the shaft. I do have it aligned correctly, and I tightened the bolts down really tight, but after a couple months it's just starting to come loose again. I'll torque the bolts down again, this time with a 3' bar.
#615
#616
Legacy TMS Member
Join Date: August 14, 2005
Location: Spangdahlem Air Base Germany
Posts: 1,217
Likes: 0
Received 0 Likes
on
0 Posts
I had the same problem with the shift **** shaft spinning, did the same thing, messed around with the **** itself for a while until I figured out it was the shaft. I do have it aligned correctly, and I tightened the bolts down really tight, but after a couple months it's just starting to come loose again. I'll torque the bolts down again, this time with a 3' bar.
#618
George...
I was going to wait for a picture of the new shaft, but curiosity is getting the best of me...
Two questions... is the new MGW ball going to be in black only and is the new shaft just a change to 12mm X 1.75 threads...
I was hoping it was going to be a flat handle.
Bobby M.
I was going to wait for a picture of the new shaft, but curiosity is getting the best of me...
Two questions... is the new MGW ball going to be in black only and is the new shaft just a change to 12mm X 1.75 threads...
I was hoping it was going to be a flat handle.
Bobby M.
#619
hi
I got my MGW shifter installed last week. 8 turns out. I love the shift - springs are fine, throw is great, position is good. Only issue I'm having is quite a loud rattle from the shifter while accelerating fairly hard in the 3-5k rpm range (rest of the time it's silent). I've read through this whole long thread and don't think anyone else reported this issue - which is good, I assume maybe I just need to check something. It's all installed properly tight, far as I know.
any suggestions George, or others?
thanks
Daz
I got my MGW shifter installed last week. 8 turns out. I love the shift - springs are fine, throw is great, position is good. Only issue I'm having is quite a loud rattle from the shifter while accelerating fairly hard in the 3-5k rpm range (rest of the time it's silent). I've read through this whole long thread and don't think anyone else reported this issue - which is good, I assume maybe I just need to check something. It's all installed properly tight, far as I know.
any suggestions George, or others?
thanks
Daz
#620
Legacy TMS Member
Join Date: August 14, 2005
Location: Spangdahlem Air Base Germany
Posts: 1,217
Likes: 0
Received 0 Likes
on
0 Posts
Check your brake handle. George posted a video a few pages back on how to get rid of it. I tried and it didn't work, but it's because the plastic piece of the handle isn't coming back together well. I gotta figure that out...it's driving me nuts.