Ponies on The Run (Again)
GTR Member
Join Date: January 26, 2006
Location: Central Florida
Posts: 4,639
Likes: 0
Received 0 Likes
on
0 Posts
I did get my "TURBOCHARGED" emblems but didn't like them, so I ordered new ones from Moss Mustang. Hopefully they will be better. They'll be here on Monday 3/3, so I'll take pictures of them taped on so we can figure out what looks best.
Also, I'm installed my Mechanical Water Temp gauge fitting into the boss on the passenger side of the intake, right were the water leaves the engine to go to the radiator. I think this is the best place to take an accurate reading, but will also be the most difficult place to install the fitting.
I'll have to drain down the coolant and remove the radiator hose so I can stuff a rag in there to catch the aluminum filings. Then I'll drill a hole and tap it to 1/2" NPT. That's the size of the fitting for a mechanical gauge since a bulb drops down into the intake to measure the temperature.
Also, I'm installed my Mechanical Water Temp gauge fitting into the boss on the passenger side of the intake, right were the water leaves the engine to go to the radiator. I think this is the best place to take an accurate reading, but will also be the most difficult place to install the fitting.
I'll have to drain down the coolant and remove the radiator hose so I can stuff a rag in there to catch the aluminum filings. Then I'll drill a hole and tap it to 1/2" NPT. That's the size of the fitting for a mechanical gauge since a bulb drops down into the intake to measure the temperature.
Legacy TMS Member
I'm thinking about ordering mine today.
Almost had me there for a second.. thanks Tom.
Cobra Member
Join Date: May 17, 2007
Location: Texa$
Posts: 1,201
Likes: 0
Received 0 Likes
on
0 Posts
Jed, you've been somewhat quiet on the mod front, time to step up to the plate again and get some forged internals pal. With all that pocket change you seem to have whats a few more K of spending, right Bill
Congrats on the 500 George!
If it weren't for POTR, you'd still be in the double digits.
GTR Member
Join Date: January 26, 2006
Location: Central Florida
Posts: 4,639
Likes: 0
Received 0 Likes
on
0 Posts
What are you gapping your plugs to?
Only concern is how long in length the emblems are. Most all I've seen are 5 to 6+", whereas the autobadges are only 3.7".
I was told by Brenspeed to leave them as is (out of box gapping). They mentioned that in other FI applications (turbo, TS, or high boost), plugs need to be re-gapped.
GTR Member
Join Date: January 26, 2006
Location: Central Florida
Posts: 4,639
Likes: 0
Received 0 Likes
on
0 Posts
I'll check out the Moss website to see how they look like.
Only concern is how long in length the emblems are. Most all I've seen are 5 to 6+", whereas the autobadges are only 3.7".
I was told by Brenspeed to leave them as is (out of box gapping). They mentioned that in other FI applications (turbo, TS, or high boost), plugs need to be re-gapped.
Only concern is how long in length the emblems are. Most all I've seen are 5 to 6+", whereas the autobadges are only 3.7".
I was told by Brenspeed to leave them as is (out of box gapping). They mentioned that in other FI applications (turbo, TS, or high boost), plugs need to be re-gapped.
Yeah... I had to re-gap to .038". Plus, you would need the special gapping tool.
Any longer in length under the GT will look goofy IMO.
(plugs) I told them that I don't have one of those gapping tools, so if they needed to be gapped, I asked if they can do it for me prior to shipping.
I found 2 other 'maybe's'..
This one is actually a Chevy part (looks good though) 4 1/4 x 3/8
Attachment 40000
Generic emblem 5 1/2 x 1/2
Attachment 39999
Still looks like I may be getting the ones from Autobadges.
This one is actually a Chevy part (looks good though) 4 1/4 x 3/8
Attachment 40000
Generic emblem 5 1/2 x 1/2
Attachment 39999
Still looks like I may be getting the ones from Autobadges.
GTR Member
Join Date: January 26, 2006
Location: Central Florida
Posts: 4,639
Likes: 0
Received 0 Likes
on
0 Posts
I found 2 other 'maybe's'..
This one is actually a Chevy part (looks good though) 4 1/4 x 3/8
Attachment 40000
Generic emblem 5 1/2 x 1/2
Attachment 39999
Still looks like I may be getting the ones from Autobadges.
This one is actually a Chevy part (looks good though) 4 1/4 x 3/8
Attachment 40000
Generic emblem 5 1/2 x 1/2
Attachment 39999
Still looks like I may be getting the ones from Autobadges.
These are the emblems from Moss Mustang: