2013 HIDs on a 2012 Halogen
#1
Mach 1 Member
Thread Starter
2013 HIDs on a 2012 Halogen
I have been working on buttoning up my 2013 retrofit on my 2012 and the last thing I need to do is swap the headlamps. Not only to look nice but the color difference between the 2012 bulbs and the led fogs are god awful. I know there are a few threads floating around but they died off, I really need information on the harness, Everything I need for them and where to obtain the parts. I already found the plugs and capacitors, Lexiion if you have any input it would be greatly appreciated.
#2
Mach 1 Member
I have been working on buttoning up my 2013 retrofit on my 2012 and the last thing I need to do is swap the headlamps. Not only to look nice but the color difference between the 2012 bulbs and the led fogs are god awful. I know there are a few threads floating around but they died off, I really need information on the harness, Everything I need for them and where to obtain the parts. I already found the plugs and capacitors, Lexiion if you have any input it would be greatly appreciated.
Let me know what you want to do and I am willing to help you out. I actually have a 2013 SJB that you could use to try.
Or you go full throttle and buy a 2013 V6 light harness and a 2013 SJB and just replace the whole thing.... but $$
LEXiiON
Last edited by LEXiiON; 5/1/16 at 07:15 PM.
The following users liked this post:
awoychosky123 (5/7/16)
#4
Mach 1 Member
LEXiiON
The following users liked this post:
awoychosky123 (5/7/16)
#6
Mach 1 Member
Yes...
You don't even need to reprogram the SJB for the switchback. That's done through PIN3 at the HIDs. You need to reprogram the SJB for the high beams.. It needs to power the low beams when you are on high beams, as on the HIDs that's just a shutter solenoid.
LEXiiON
Last edited by LEXiiON; 5/1/16 at 08:23 PM.
The following users liked this post:
awoychosky123 (5/7/16)
#7
Mach 1 Member
Thread Starter
What do you have in terms of as-built codes for me to use?
Also thanks a bunch I didn't even know where to start on this project.
Also thanks a bunch I didn't even know where to start on this project.
Last edited by awoychosky123; 5/1/16 at 08:26 PM.
#8
Mach 1 Member
GEM 726-02-01 03C0 2020 0033
GEM 726-03-01 0140 72
GEM 726-04-01 0234
GEM 726-05-01 040C 43
GEM 726-06-01 0000 34
GEM 726-07-01 2505 5F
GEM 726-08-01 0105 0A46
GEM 726-09-01 C000 F7
GEM 726-10-01 8008 0000 00C6
GEM 726-10-02 0000 0000 003F
GEM 726-10-03 0000 0000 0040
GEM 726-10-04 0000 41
GEM 726-11-01 1400 53
The following users liked this post:
awoychosky123 (5/7/16)
#10
Mach 1 Member
#13
Mach 1 Member
The following users liked this post:
awoychosky123 (5/7/16)
#15
Mach 1 Member
Thread Starter
Never mind I answered my own question links if people need them
2013 Turn signal connector: http://www.tascaparts.com/oe-ford/3u2z14s411fhab
2013 HID Connector: http://www.tascaparts.com/oe-ford/cu2z14s411ada
2013 Turn signal connector: http://www.tascaparts.com/oe-ford/3u2z14s411fhab
2013 HID Connector: http://www.tascaparts.com/oe-ford/cu2z14s411ada
The following users liked this post:
awoychosky123 (5/7/16)
#19
Mach 1 Member
The following users liked this post:
awoychosky123 (5/7/16)
#20
Mach 1 Member
Thread Starter
What about the parking light/turn signal I see that the turn signal bulb uses the same wires as the led appears to use. Did ford slip these wires so I have one for both the bulbs and the leds?