GT500 Pedal Covers
8/26/07, 01:03 AM
#22
Thanks now I got outbid!! 
Here ya go.
http://cgi.ebay.com/ebaymotors/Musta...spagenameZWDVW
But ya otta jump on ShowGT's offer....doesn't get any better than that....
Mike
http://cgi.ebay.com/ebaymotors/Musta...spagenameZWDVW
But ya otta jump on ShowGT's offer....doesn't get any better than that....
Mike
8/26/07, 10:52 AM
#24
GT Member
Thread Starter
Join Date: April 11, 2007
Location: Canada
Posts: 154
Likes: 0
Received 0 Likes
on
0 Posts
sorry I couldn't reply sooner but thanks guys for all the response. I will get these of ebay then and I will try some of the recommended installation methods
8/26/07, 11:26 AM
#25
GT Member
Join Date: October 17, 2004
Posts: 137
Likes: 0
Received 0 Likes
on
0 Posts
Hey Igor:
More Mustang Manual Transmission Pedals here. I have the UPR ones and am happy with them. The GT500 ones are nice but a bit pricey I agree.
More Mustang Manual Transmission Pedals here. I have the UPR ones and am happy with them. The GT500 ones are nice but a bit pricey I agree.
8/26/07, 06:22 PM
#26
Legacy TMS Member
FYI...you can order them direct from the builder Aac4parts@aol.com. Address email to Craig. They supply the pedals for most of the distributers. They are identicle to the ones Ford sells, same for CDC
8/30/07, 05:22 PM
#30
GT Member
Thread Starter
Join Date: April 11, 2007
Location: Canada
Posts: 154
Likes: 0
Received 0 Likes
on
0 Posts
I have finally got my pedals installed and I thought I'd share some pictures. The install was quite easy after soaking the pedals in hot water like you guys said. I am very pleased with the new look and now I'm hungry for more mods 
9/4/07, 10:31 PM
#31
Mach 1 Member
Join Date: June 8, 2004
Posts: 528
Likes: 0
Received 0 Likes
on
0 Posts
A great find! Also ordered from Craig and installed them earlier today.
Very easy after soaking the brake and clutch pedals in hot water for a few minutes. Just boiled a couple of cups of hot water in the microwave, poured into a plastic container and soaked the 2 pedals for a few minutes.
Also put a little bit of soap on the brake and clutch, and they slipped on without any tools - except my fingers. I was a bit concerned that they seemed a bit loose, but once the pedals cooled off, they were solid.
Very easy after soaking the brake and clutch pedals in hot water for a few minutes. Just boiled a couple of cups of hot water in the microwave, poured into a plastic container and soaked the 2 pedals for a few minutes.
Also put a little bit of soap on the brake and clutch, and they slipped on without any tools - except my fingers. I was a bit concerned that they seemed a bit loose, but once the pedals cooled off, they were solid.
9/5/07, 06:47 PM
#33
Shelby GT500 Member
LOL @ the Ultimate pedal instruction. "A few minutes to let the rubber cool off." You mean the metal! Ouch!
But ya, very easy mod and great looks! I did the boiling water thing. No soap, just fingers and worked the boots around the pedals. Be sure you align the gas boot before you place it. When that 3M stuff sticks, it sticks!
Got mine via Craig as well...through ebay! Didn't know about direct emailing until after I bidded. I was hoping one of y'all would snipe me! In the end, only paid $1.75 more than getting from him direct.
I am very
with this.
But ya, very easy mod and great looks! I did the boiling water thing. No soap, just fingers and worked the boots around the pedals. Be sure you align the gas boot before you place it. When that 3M stuff sticks, it sticks!
Got mine via Craig as well...through ebay! Didn't know about direct emailing until after I bidded. I was hoping one of y'all would snipe me! In the end, only paid $1.75 more than getting from him direct.
I am very
with this.
9/7/07, 08:39 PM
#35
Mach 1 Member
Join Date: August 31, 2006
Posts: 644
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys, I've also joined the "getting old waiting for CDC to make those dead pedals" club. You may have seen some of my posts about contacting Patrick at CDC. He kept saying it would be out very soon....they had all the designs...just needed to check a few things...Oh sorry something came up...We don't know when they'll be out.
I give up.
I give up.
9/8/07, 11:29 AM
#37
Hey guys, I've also joined the "getting old waiting for CDC to make those dead pedals" club. You may have seen some of my posts about contacting Patrick at CDC. He kept saying it would be out very soon....they had all the designs...just needed to check a few things...Oh sorry something came up...We don't know when they'll be out.
I give up.
I give up.
9/8/07, 09:56 PM
#38
Shelby GT500 Member
Join Date: April 25, 2007
Location: Kansas City, MO
Posts: 2,955
Likes: 0
Received 2 Likes
on
2 Posts
Johnathan, drop Craig an email @ Aac4parts@aol.com and mention you are wanting a set of Mustang pedals for 2005 + He will take care of you, either Paypal or you can send a payment.
9/13/07, 08:54 PM
#39
Shelby GT350 Member
Join Date: April 9, 2007
Location: Ellenton, FL
Posts: 2,463
Likes: 0
Received 0 Likes
on
0 Posts
Johnathan, drop Craig an email @ Aac4parts@aol.com and mention you are wanting a set of Mustang pedals for 2005 + He will take care of you, either Paypal or you can send a payment.
Thanks