My KITT Mustang Replica Completed
V6 Member
Joined: September 12, 2009
Posts: 74
Likes: 0
Thread Starter
Legacy TMS Member
Joined: August 9, 2004
Posts: 407
Likes: 2
From: Mount Dora, Florida
HAPPY NEW YEAR ALL!!
Tamatt27, could you tell me the measurements of your lemans stripes? I am going to get mine done soon, and I can't find the proper measurements anywhere on the net. I am guessing that they are 8".
Thanks
Tamatt27, could you tell me the measurements of your lemans stripes? I am going to get mine done soon, and I can't find the proper measurements anywhere on the net. I am guessing that they are 8".
Thanks
Member
Joined: February 27, 2006
Posts: 3
Likes: 0
Good mod!
But... What about windshield nozzle, Did you change its location? and
Did you cover the heat extraction? If not What happen when its rain?
Other question... When did you found the over hood red lights?
Thanks,
But... What about windshield nozzle, Did you change its location? and
Did you cover the heat extraction? If not What happen when its rain?
Other question... When did you found the over hood red lights?
Thanks,
Thread Starter
Legacy TMS Member
Joined: August 9, 2004
Posts: 407
Likes: 2
From: Mount Dora, Florida
Thanks! I got the CDC wiper nozzle relocation kit...mounts them on the wiper arm. The heat extractors are not covered, but rain has caused no issues. I figure water comes in from the underside in the rain too!
As for the hood light, it was custom made for me. It has 160 Hi powered LED's and 32 transistors to up power the 12V. The link to his Ebay auctions is:
http://cgi.ebay.com/ebaymotors/ws/eB...%3AMEWAX%3AVRI
I had him add the 2 up power options for a total of $400.00 delivered
As for the hood light, it was custom made for me. It has 160 Hi powered LED's and 32 transistors to up power the 12V. The link to his Ebay auctions is:
http://cgi.ebay.com/ebaymotors/ws/eB...%3AMEWAX%3AVRI
I had him add the 2 up power options for a total of $400.00 delivered
Last edited by bill0754; Jan 3, 2010 at 02:13 PM.
Thread Starter
Legacy TMS Member
Joined: August 9, 2004
Posts: 407
Likes: 2
From: Mount Dora, Florida
OK...added the Matte stripes
I finally gave in and did the matte stripes. I also redid my interior lighting to be closer to the TV car. I also added the Ford Factory Navigation system. Couldn't resist...$599 on Ebay! I also added 2010 Lower door speaker trim, and a full Roush carbon fiber dash kit.
You'll have to excuse the messy garage!! It's in the low 30's here in Florida and raining, so I couldn't take KITT outside to take new photos.
You'll have to excuse the messy garage!! It's in the low 30's here in Florida and raining, so I couldn't take KITT outside to take new photos.
Last edited by bill0754; Jan 8, 2010 at 04:51 PM.
Thread Starter
Legacy TMS Member
Joined: August 9, 2004
Posts: 407
Likes: 2
From: Mount Dora, Florida
Thanks for the compliments!!
As for the lighting, I did the interior with LED light stripes, then custom made covers from ceiling lighting panels from Home Depot. I added a high power single LED in the front footwells, 2 in the rear console, and one in the cupholder. I hardwired them all to the powerpoint in the console and put a switch inside the console to activate them. The front scanner was custom made, and I had to take a dremel to the inside of the hood on the air box for install. Finally the underbody lights were installed with plenty of 4 letter words!! I will never do those again!!
As for the lighting, I did the interior with LED light stripes, then custom made covers from ceiling lighting panels from Home Depot. I added a high power single LED in the front footwells, 2 in the rear console, and one in the cupholder. I hardwired them all to the powerpoint in the console and put a switch inside the console to activate them. The front scanner was custom made, and I had to take a dremel to the inside of the hood on the air box for install. Finally the underbody lights were installed with plenty of 4 letter words!! I will never do those again!!
Cobra Member
Joined: November 30, 2005
Posts: 1,014
Likes: 0
From: Dallas, TX
Thanks for the compliments!!
As for the lighting, I did the interior with LED light stripes, then custom made covers from ceiling lighting panels from Home Depot. I added a high power single LED in the front footwells, 2 in the rear console, and one in the cupholder. I hardwired them all to the powerpoint in the console and put a switch inside the console to activate them. The front scanner was custom made, and I had to take a dremel to the inside of the hood on the air box for install. Finally the underbody lights were installed with plenty of 4 letter words!! I will never do those again!!
As for the lighting, I did the interior with LED light stripes, then custom made covers from ceiling lighting panels from Home Depot. I added a high power single LED in the front footwells, 2 in the rear console, and one in the cupholder. I hardwired them all to the powerpoint in the console and put a switch inside the console to activate them. The front scanner was custom made, and I had to take a dremel to the inside of the hood on the air box for install. Finally the underbody lights were installed with plenty of 4 letter words!! I will never do those again!!
I've been looking for something to house my LEDs that are not by my feet.... I might have to check out these panels...
Cobra Member
Joined: November 30, 2005
Posts: 1,014
Likes: 0
From: Dallas, TX
And the ONLY thing I don't like on the car is those rear light covers.... mainly because it reminds me when I had them and how crappy they fit. If you don't need to take them on and off I would highly recommend grabbing some VHT night shade. I love it on mine.
Car looks amazing either way though
What kind of rear valance is that?
Car looks amazing either way though
What kind of rear valance is that?
Last edited by WuTimeUT; Jan 15, 2010 at 01:05 AM.