I've decided to go with one of these two ducktails. Looking for general opinions on which one looks better as well as comments from anyone that has these. Fit, quality, and how did you mount it i.e. drill or no drill.

Footnote: Each spoiler comes with additional bolts requiring drilling new holes; however, according to Cervinis they can also be mounted with just good prep and tape.

Black car is the Foose, Tungsten is the Cervinis, and the Satin Silver is my car.

 

I can't give any info on the ducktails, but I can tell you that I like the gt500 wing on your car now. I would personally leave it the way it is! Your car looks really nice.

 

Quick,
Buy them both for cheap!

http://www.classicdesignconcepts.com...oduct_list&c=8

But IMHO, I like the foose better b/c it doesn't travel quite as high. Also, with the CDC, you will either have to fill your holes or buy the nifty hole filler brackets which are ok

 

Personally I like the spoiler you have on there a lot better than the other two. That's just my opinion.

Very nice ride by the way.

 

I voted Foose.. I'm a bit biased as that black car is mine :-)

-danny

 

Cervini was a PITA to install. I like it after all the headaches, but if I knew what I was getting into I'd have gone with the Foose. Especially if you can get it pre-painted.

BTW I had to drill holes in my rear fender to mount the Cervini so there's no easy way for me to go back now.

 

Holes were drilled in my rear right above the lights for mounting the Foose. So, no going back for me either

-danny

 

Hey Danny,
What did they do to keep it from leaking and rusting???

I have mine to install and was wondering.

Also, did you do it yourself... Any tips?

Finally, do you have more pictures of the trunk part and closer to the body.

 

I vote GT500

 

Very nice car. If I do go this route, I will try my luck without drilling.

 

i dont know anything about ducktail spoilers but i think that the GT500 one that you have looks great.

and Danny I love lookin at pics of your car. yours is the only one i think i would ever want to cheat on mine with haha.

 

I voted cervinis, but that is what I have. I just used the stock mounting holes. I prepped the surface and stuck the rest on, not one problem. Have been on the car for almost a year.

 

I went with the Foose From CDC as it is painted.Color is right on. Fit was good.Install went fine the timplets fo drilling wher right on.I used tuchup paint after drilling the holes.Then Clear sylicone when installed

 

Do you have any more pics?

It looks great, although I wish the seam on the fender ran all the way down to the bumper like the street scene and CDC. Very un Foose like to not do that.

 

Here is a a side vew from test fit

 

I chose the Cervini Ducktail for the look of course, but my concern was the law regarding that third break light and the removal of it. I had my body shop install as they were doing all the painting/striping ect.. I have no leaks. I did however remove my stainless steel bezels since this picture was taken. BTW, your ride looks fine the way it is.

 

I voted Cervinis......I was on the fence about these, because it almost looks like it might be a little too much, but once I saw it in person, I was hooked. Some of the other ducktails look good from the back, but when viewed from the side or looking back from the front, theres just this little bump.

 

I would vote Cervini's, but not the "C", I like the type III one, is more balanced in size.

 

dibbs on your GT500 wing!!!

i like the foose.. but have reservations about the corner pieces sticking out.. On the black, is isnt as noticable.. but it is on the blue... and probably would still be on the silver.

 

more people need to use the foose. it looks soooo much better than the cervinis. the Cervinis is too large imo.