Tuned By Bamachips - Getting P061b with limp mode
6/19/07, 02:18 AM
#1
GT Member
Thread Starter
Join Date: February 13, 2004
Posts: 165
Likes: 0
Received 0 Likes
on
0 Posts
Tuned By Bamachips - Getting P061b with limp mode
My computer: FBNF1G3
My Mods: FRPP Delete Plates, Steeda UDPs, Coast Driveline 4" DS, C&L racer, and 93 race/tq 87 perf tunes from Doug. I'm getting P061b usually when running hard through 1st and 2nd. I think I managed to make it happen once in 3rd. It seems like everytime I hit limp mode... I feel the car slightly bogging down then a quick burst of power and the nasty w(r)ench shows up. Sometimes it throws P061b and sometimes there is no code.
Any help would be greatly appreciated. I have a couple of messages in to Doug but I know he's busy so I'm wondering if anyone else has had this problem.
My Mods: FRPP Delete Plates, Steeda UDPs, Coast Driveline 4" DS, C&L racer, and 93 race/tq 87 perf tunes from Doug. I'm getting P061b usually when running hard through 1st and 2nd. I think I managed to make it happen once in 3rd. It seems like everytime I hit limp mode... I feel the car slightly bogging down then a quick burst of power and the nasty w(r)ench shows up. Sometimes it throws P061b and sometimes there is no code.
Any help would be greatly appreciated. I have a couple of messages in to Doug but I know he's busy so I'm wondering if anyone else has had this problem.
6/19/07, 09:32 AM
#2
Mach 1 Member
Join Date: May 17, 2006
Posts: 939
Likes: 0
Received 0 Likes
on
0 Posts
Found this on SCT's site...
Q: I just installed my CAI on my 2005 mustang gt and used an 87 octane tune from a dealer. I drove it around a bit and then got a CEL and the message center displayed FAILSAFE ENGINE MODE. I checked the SCT2 and got these codes. P061b, P2106.
A: You need to make sure they setup your tune for the cold air kit. If they didn't you will have problems with the CEL light and it going into failsafe mode
I think you need to talk to Doug. That P061B code is a wierd one. It doesn't show up on any OBD II Ford code lists. I can only find it referenced on 5.4L 3V truck TSB's.
Q: I just installed my CAI on my 2005 mustang gt and used an 87 octane tune from a dealer. I drove it around a bit and then got a CEL and the message center displayed FAILSAFE ENGINE MODE. I checked the SCT2 and got these codes. P061b, P2106.
A: You need to make sure they setup your tune for the cold air kit. If they didn't you will have problems with the CEL light and it going into failsafe mode
I think you need to talk to Doug. That P061B code is a wierd one. It doesn't show up on any OBD II Ford code lists. I can only find it referenced on 5.4L 3V truck TSB's.
6/19/07, 02:23 PM
#3
FR500 Member
Join Date: August 23, 2004
Posts: 3,153
Likes: 0
Received 0 Likes
on
0 Posts
P061b (internal control module torque calculation) Torque Management
P2106 (Throttle Actuator Control System - Forced Limited Power) Failsafe Mode
Just search with Google the following terms: [your error code] OBDII error code
Hopefully Doug gets back to you soon
P2106 (Throttle Actuator Control System - Forced Limited Power) Failsafe Mode
Just search with Google the following terms: [your error code] OBDII error code
Hopefully Doug gets back to you soon
Thread
Thread Starter
Forum
Replies
Last Post