General Mustang Chat Not Model Year Specific

GT350 for sale.

Old Aug 5, 2006 | 07:14 AM
  #1  
tricky02GT's Avatar
Thread Starter
Mach 1 Member
 
Joined: January 22, 2006
Posts: 614
Likes: 0
GT350 for sale.

What years did they produce the GT350? There is a red one up the road nfrom me for sale. I need to take a closer look at it and speak to the seller and when I do I will take some pics for everyone. It looks like 65 or 66 styling? The paintwork looked ok but I was driving past and didnt have the time to stop.
Reply
Old Aug 5, 2006 | 07:53 AM
  #2  
TMSBrad's Avatar
The Mustang Source FOUNDER
 
Joined: January 29, 2004
Posts: 9,890
Likes: 11
From: Vestavia Hills, Ala.
1965-1970 & 1984 1/2

If it's a '66 it'll have a back seat. All '65s only had the front buckets. A '66 will have a quarter window whereas the '65s had louvers. A '65 will have a smooth side scallop and a '66 will have a scoop.

1965:


1966:

Reply
Old Aug 5, 2006 | 08:18 AM
  #3  
mudshuvel319's Avatar
Mach 1 Member
 
Joined: January 2, 2006
Posts: 534
Likes: 0
Make sure its real. There are a ton of clones out there, and the real ones are pretty expensive. if the car's only $30-40k, its not real. If you want a clone, they are pretty nice, but do make sure you know what it is.
Reply
Old Aug 5, 2006 | 09:35 AM
  #4  
tricky02GT's Avatar
Thread Starter
Mach 1 Member
 
Joined: January 22, 2006
Posts: 614
Likes: 0
Anything in particular I should be looking for? Badge on engine bay or anything?
Reply
Old Aug 5, 2006 | 10:11 AM
  #5  
markboss's Avatar
Member
 
Joined: July 24, 2006
Posts: 40
Likes: 0
Look for a Shelby Vin Plate on the drivers side inner fender, should have a SFM......... sequential number, and this number will be stamped in the psgr side inner fender apron, near the shock tower....

Under this driver side vin plate will be a ford vin number, must have a "K" as the 5th digit.."289 hipo" in order to be a Shelby...

Also look for traction bar setup on rear end, overides, or underides, depending on year....,Check for 289 hipo harmonic balancer,,,should be about 2" thick, versus 1" thick for normal 289....

Hipo Alternator Pulley 4" diameter, racing seatbelts, not mustang...66 will have a Cobra tach, on top of dash, 65 will have a pod on dash with tach, oil presure gauge....

If it's real, it will not be had to see the difference...

Mark
Attached Images  
Attached Images
File Type: bmp
hooters shelby crop.bmp (350.0 KB, 206 views)
Reply
Old Aug 5, 2006 | 11:23 AM
  #6  
TMSBrad's Avatar
The Mustang Source FOUNDER
 
Joined: January 29, 2004
Posts: 9,890
Likes: 11
From: Vestavia Hills, Ala.
Reply
Old Aug 5, 2006 | 11:30 AM
  #7  
tricky02GT's Avatar
Thread Starter
Mach 1 Member
 
Joined: January 22, 2006
Posts: 614
Likes: 0
Originally Posted by markboss
Look for a Shelby Vin Plate on the drivers side inner fender, should have a SFM......... sequential number, and this number will be stamped in the psgr side inner fender apron, near the shock tower....

Under this driver side vin plate will be a ford vin number, must have a "K" as the 5th digit.."289 hipo" in order to be a Shelby...

Also look for traction bar setup on rear end, overides, or underides, depending on year....,Check for 289 hipo harmonic balancer,,,should be about 2" thick, versus 1" thick for normal 289....

Hipo Alternator Pulley 4" diameter, racing seatbelts, not mustang...66 will have a Cobra tach, on top of dash, 65 will have a pod on dash with tach, oil presure gauge....

If it's real, it will not be had to see the difference...

Mark
Holy crap dude!! Look for vin would have been fine!!!!
WOW.
Reply
Old Aug 5, 2006 | 07:29 PM
  #8  
markboss's Avatar
Member
 
Joined: July 24, 2006
Posts: 40
Likes: 0
You will find there are far more fakes than real 65-66 Shelbys......Only about 2600 real cars for the total of both years....take into account the number that have been destroyed....probably about half survived...

When big money is at stake, you will have rebodies, and fake Vin's....

If you need an opinion, let me know, been doing this for about 25 years...

Mark
Reply
Old Aug 6, 2006 | 03:30 AM
  #9  
tricky02GT's Avatar
Thread Starter
Mach 1 Member
 
Joined: January 22, 2006
Posts: 614
Likes: 0
Hope to go take a look at it today. I know I could never afford it but I will see what he is asking for it all the same. Maybe somebody on here might want it. Heard that a lot of people have been stopping and looking at it.
Also thanx for the advice Mark.
Reply
Old Aug 13, 2006 | 11:28 AM
  #10  
codeman94's Avatar
 
Joined: December 14, 2004
Posts: 7,933
Likes: 16
From: Goshen, IN
well???
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
CNFLCTD
GT350
4
Aug 4, 2017 07:08 AM
Steve@CJPP
Vendor Showcase
1
Sep 24, 2015 06:58 PM
HizliBullet
GT350
0
Sep 15, 2015 09:13 PM
Steve@CJPP
Vendor Showcase
0
Sep 3, 2015 10:43 AM


Thread Tools
Search this Thread

All times are GMT -6. The time now is 01:04 PM.