What have you done to/with your Boss 302 this week?
#161
Yep, for guys like me we would be lucky to see much of a gain but we have some real racers here and I would hope they see more of a difference.
#163
#164
V6 Member
Join Date: March 7, 2011
Location: Moscow Russia and NC USA
Posts: 82
Likes: 0
Received 1 Like
on
1 Post
That does look good, with all the talk about doing this so far I think you are the only that did it. Did they say anything about it being plug and play, just connect it into existing wire harnesses? If I did anything like this I think I would go all temps like oil, trans rear and engine. With the ability of the engine to go into limp mode I personally don't see much of a need for oil pressure. By the time you even see it the car would be in limp mode anyway. It seems to me for tracking it is all about temps.
http://www.boss302forum.com/index.ph...triple-guages/
#165
Bullitt Member
Join Date: March 15, 2011
Location: SE Michigan
Posts: 279
Likes: 0
Received 0 Likes
on
0 Posts
DONE!
I think it looks better than the Faux! I think it actually looks like it was intended.
Gary, I give you all the credit. I would have never had the Cahounas to try this one on my own!
Its plenty sturdy, the plastic is thick. I would expect no reduction in strength. The Grill was painted body color and then masked off and painted black. So, I touched up the areas that showed a small bit of body color paint from the drilling process with some flat black paint and a Q-Tip. It looks great and I'm a perfectionist!
And here is Mod # 3 for this week end!
I think it looks better than the Faux! I think it actually looks like it was intended.
Gary, I give you all the credit. I would have never had the Cahounas to try this one on my own!
Its plenty sturdy, the plastic is thick. I would expect no reduction in strength. The Grill was painted body color and then masked off and painted black. So, I touched up the areas that showed a small bit of body color paint from the drilling process with some flat black paint and a Q-Tip. It looks great and I'm a perfectionist!
And here is Mod # 3 for this week end!
Last edited by Bossdog; 6/30/11 at 04:42 AM.
#167
That is a transmission scoop
#168
Shelby GT350 Member
Join Date: November 20, 2010
Location: Sioux Falls, SD
Posts: 2,384
Likes: 0
Received 1 Like
on
1 Post
Nice work Bossdog. I agree, it looks more factory than the original. I still think this is what they had in mind given the pattern on there. I looked at mine again this morning and the honeycomb "fake" mesh structure actually creates the radius edge that PTRocks recommended, so I'm not sure chamfering is necessary.
What specifically did you buy for touch up paint? The areas where I drilled only have a couple small spots of orange, but I've picked up several rock chips in the other parts of the grille that could use touching up.
What specifically did you buy for touch up paint? The areas where I drilled only have a couple small spots of orange, but I've picked up several rock chips in the other parts of the grille that could use touching up.
#169
I'm not planning anything as exciting as you guys, but once my joints cooperate, I'll be using this:
The center section is removable to allow for easier access. I need to make sure I put it back in position before driving off! The wheel chock block is removable to allow placing the sloping ramps in front to drive off forwards, if necessary.
The center section is removable to allow for easier access. I need to make sure I put it back in position before driving off! The wheel chock block is removable to allow placing the sloping ramps in front to drive off forwards, if necessary.
#170
Tasca Super Boss 429 Member
Join Date: December 18, 2010
Location: NorCal
Posts: 3,708
Likes: 0
Received 0 Likes
on
0 Posts
I'm not planning anything as exciting as you guys, but once my joints cooperate, I'll be using this:
The center section is removable to allow for easier access. I need to make sure I put it back in position before driving off! The wheel chock block is removable to allow placing the sloping ramps in front to drive off forwards, if necessary.
The center section is removable to allow for easier access. I need to make sure I put it back in position before driving off! The wheel chock block is removable to allow placing the sloping ramps in front to drive off forwards, if necessary.
#172
The ramps by themselves are real nice. If you get a set of the long ones, I'd suggest going with the two piece set for convenience of storage. Make sure you check what slope you need. Low cars (or long overhangs like what happens with the LS splitter in place), require the extensions.
Last edited by 1FAFP90; 6/30/11 at 09:22 AM.
#173
Bullitt Member
Join Date: August 3, 2007
Location: Florida
Posts: 349
Likes: 0
Received 0 Likes
on
0 Posts
I'm not planning anything as exciting as you guys, but once my joints cooperate, I'll be using this:
The center section is removable to allow for easier access. I need to make sure I put it back in position before driving off! The wheel chock block is removable to allow placing the sloping ramps in front to drive off forwards, if necessary.
The center section is removable to allow for easier access. I need to make sure I put it back in position before driving off! The wheel chock block is removable to allow placing the sloping ramps in front to drive off forwards, if necessary.
Can you say car shows
#174
#175
Hey Gary, are you gonna put an LS front splitter on your car to balance out the rear spoiler?
#178
Bullitt Member
Join Date: March 15, 2011
Location: SE Michigan
Posts: 279
Likes: 0
Received 0 Likes
on
0 Posts
Nice work Bossdog. I agree, it looks more factory than the original. I still think this is what they had in mind given the pattern on there. I looked at mine again this morning and the honeycomb "fake" mesh structure actually creates the radius edge that PTRocks recommended, so I'm not sure chamfering is necessary.
What specifically did you buy for touch up paint? The areas where I drilled only have a couple small spots of orange, but I've picked up several rock chips in the other parts of the grille that could use touching up.
What specifically did you buy for touch up paint? The areas where I drilled only have a couple small spots of orange, but I've picked up several rock chips in the other parts of the grille that could use touching up.
For paint I just used what I had on the shelf, Krylon Flat black. I sprayed it in a Snapple Cap and used a Q-Tip. It worked really well
#180
FR500 Member
Join Date: July 1, 2008
Location: Oxford, UK
Posts: 3,336
Likes: 0
Received 0 Likes
on
0 Posts