Body Work
#262
Super Boss Lawman Member
Thread Starter
Anyone here want to trade a 3.03 Toploader 3 speed for a 67-68 Mustang GT rear valance? I still have my old 3 speed and would like to get rid of it for something I could actually use.
This is the valance:
This is the valance:
#265
Super Boss Lawman Member
Thread Starter
Mark, were you able to go to Larrys yesterday? If so has anything been done to the 67? I need to know before I drop by and pick it up, because if he has started I will wait.
#266
Super Boss Lawman Member
Thread Starter
Mustang is back at home after over 3 weeks. Some parts should show up this week, and hopefully my new window regulator will show up too. If everything goes according to plan I will have it in the paint booth the second weekend in February.
#268
Super Boss Lawman Member
Thread Starter
Nothing was done in the 3+ weeks he had it. I called today and talked to him and was told it would take to much work to do anything so I picked it up.
#270
Super Boss Lawman Member
Thread Starter
I'll probably just trash them, they were the whole problem. Drivers side is pretty much too far gone to fix and the passenger side was barley save able.
I already have my stock scoops back installed. So all I have to do is finish my body work, prime it, and send it off to paint.
I already have my stock scoops back installed. So all I have to do is finish my body work, prime it, and send it off to paint.
Last edited by BA Mustang; 1/25/10 at 07:50 PM.
#272
Super Boss Lawman Member
Thread Starter
After paint I will be getting new exhaust. Going with a Magnaflow stainless steel polished muffler. This will allow me to run just a single pipe to the muffler and get duals out the back.
http://www.summitracing.com/parts/MPE-14277/
http://www.summitracing.com/parts/MPE-14277/
#273
Bullitt Member
Join Date: February 24, 2007
Location: Harvest, AL
Posts: 258
Likes: 0
Received 0 Likes
on
0 Posts
Go to Clanton Muffler in Madison. Don't just look at the price of the muffler but the total of what you get with your exhaust system. Robert is the best I have seen around since Luther Hick's place shut down 20 years ago. Buy local!
#274
Super Boss Lawman Member
Thread Starter
Clanton told me it was like $400 to do my exhaust and that the way I wanted it wouldn't work. I know they are wrong since I know someone with the same exhaust setup I wanted.
I use Jeffs Muffler.
I use Jeffs Muffler.
#275
Cobra Member
BA, Does the trans still have the bellhousing and shifter? I might have a valance to trade you. kennyg
#276
Super Boss Lawman Member
Thread Starter
I bought the valance this week. Have it in my room waiting to be painted. I would trade my trans for some taillight lenses.
I am still using the bellhousing on the 200, I do have the shifter for it.
I need an extra set to tint.
I am still using the bellhousing on the 200, I do have the shifter for it.
I need an extra set to tint.
Last edited by BA Mustang; 1/28/10 at 09:06 PM.
#277
Super Boss Lawman Member
Thread Starter
Hopefully after work tomorrow some tire places will be open and I can get my new tires mounted on my new rims.
Last edited by BA Mustang; 1/30/10 at 08:52 PM.
#278
Super Boss Lawman Member
Thread Starter
Alright, well I am almost there. I don't work tomorrow so I am going to start the tear down. I am pushing for it be in the booth the day after my birthday. That will give me time to drop it(needs about 3-4in. drop) and put it all back together by the cruise.
Last edited by BA Mustang; 2/5/10 at 05:05 PM.
#279
Super Boss Lawman Member
Thread Starter
Well it is finally being taken apart for final preparations. During this though one of my bumper brackets/supports snapped in 2. It was 43 years old and filled with mud. So now I have to order a new set of them.
#280
Super Boss Lawman Member
Thread Starter
Looks like I will be painting my interior part of the doors today. Supposed to be in the 60s so that paint should be good to go.