Ponies on The Run (Again)
Legacy TMS Member
Join Date: May 24, 2006
Location: San Diego
Posts: 7,409
Likes: 0
Received 0 Likes
on
0 Posts
Yeah that tranny was pretty ugly.
Nope it's just that today was my off day and she also had the day off so we were out and about all day.
BTW-We went and watched the new SAW movie. If you like the previous three you'll like this one.
BTW-We went and watched the new SAW movie. If you like the previous three you'll like this one.
Team Mustang Source
RET update...
new manifold arrived.
Wait, does that look like the new gen that Brian talked about?
Wait, does that look like the new gen that Brian talked about?
Last edited by TacoBill; 10/25/08 at 11:04 AM.
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
new manifold arrived.
Attachment 65341
Wait, does that look like the new gen that Brian talked about?
Is anyone here registered with S197? If so, can you repost some of the pics in this link? http://s197forum.com/forum/showpost....9&postcount=19
Non-registered users can't view attachements.
Attachment 65341
Wait, does that look like the new gen that Brian talked about?
Is anyone here registered with S197? If so, can you repost some of the pics in this link? http://s197forum.com/forum/showpost....9&postcount=19
Non-registered users can't view attachements.
Pretty! Looks like my 06 but can't say for sure unless I saw it side by side.
Jed
Team Mustang Source
check yer PMs Bill
Call me on the cell if you need to. Not too sure how close to POTR I'll be most of the day.
Call me on the cell if you need to. Not too sure how close to POTR I'll be most of the day.
Last edited by habu; 10/25/08 at 10:22 AM.
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
GTR Intercooler
Went to GTR yesterday for my intercooler install here are a few picts...
Before with the Kenne Bell stock intercooler.
Comparison Fluidyne (GT-500 model) Kenne Bell (aka stock FORD cobra intercooler).
The Fluidyne seems over twice the physical size then the orignal.
After with the Fluidyne in place, bolts up nicely to 4 bolts to the existing bumper.
All buttoned up with the new lower grill insert for a little protection to the intercooler.
Jed
Before with the Kenne Bell stock intercooler.
Comparison Fluidyne (GT-500 model) Kenne Bell (aka stock FORD cobra intercooler).
The Fluidyne seems over twice the physical size then the orignal.
After with the Fluidyne in place, bolts up nicely to 4 bolts to the existing bumper.
All buttoned up with the new lower grill insert for a little protection to the intercooler.
Jed
Legacy TMS Member
new manifold arrived.
Attachment 65341
Wait, does that look like the new gen that Brian talked about?
Attachment 65341
Wait, does that look like the new gen that Brian talked about?
Bill, from that picture that you posted, it looks like the new manifold! Oh no!
Here are the pix from the other site:
Went to GTR yesterday for my intercooler install here are a few picts...
Before with the Kenne Bell stock intercooler.
Comparison Fluidyne (GT-500 model) Kenne Bell (aka stock FORD cobra intercooler).
The Fluidyne seems over twice the physical size then the orignal.
After with the Fluidyne in place, bolts up nicely to 4 bolts to the existing bumper.
All buttoned up with the new lower grill insert for a little protection to the intercooler.
Jed
Before with the Kenne Bell stock intercooler.
Comparison Fluidyne (GT-500 model) Kenne Bell (aka stock FORD cobra intercooler).
The Fluidyne seems over twice the physical size then the orignal.
After with the Fluidyne in place, bolts up nicely to 4 bolts to the existing bumper.
All buttoned up with the new lower grill insert for a little protection to the intercooler.
Jed
Jed, that's the same HO heat exchanger that I've been running with my Saleen blower since January. On average, my IATs are 20 degrees higher than ambient temp; so when it's 80 degrees here, my IATs are around 100 degrees. Needless to say, it works very well!!!
I'm working something on the backburner (thanks to Jed and Brian).
Just waiting on word back from Greg as to whether those plates can be removed or will need a pre-09 manifold.