Ponies on The Run (Again)
Happy Birthday Jed!
4/12/11, 01:18 AM
Legacy TMS Member Pr
Happy bday Jed! 
4/12/11, 11:38 AM
Cobra Member
4/13/11, 01:57 AM
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
Ready for a cruise? 
4/13/11, 02:01 AM
Shelby GT500 Member
Join Date: November 22, 2006
Location: Planet Earth
Posts: 2,932
Likes: 0
Received 0 Likes
on
0 Posts
Thanks all for nice word about the car. I think the invested money on a modification on it already easily exceeded value of a car. I even can not make now full list of what has been installed in that car. But I still have a list of next wish mods 
Huh now you gave me a difficult one too explain but ok lets try.
First of all if you plan to buy aftermarket aluminum fuel rails and you want to polish them yourself phone producer directly and get from him naked ones - bare aluminum. You will save a lot of time on taking out anodized coating.
If you already have anodized ones you have to take anodized layer away. It is almost impossible to do that by hand. Take a drill with sandpaper pads, 240 will be ok and take out the anodized layer carefully. You can do it only from big surfaces. You can mount a drill in a vice so the fuel rail will be in your hand during that process. Do not use big drill to remove anodized layer from small surfaces as you will quickly lose edges. The small areas you have to do with small mini drill and sand pads – you need dremel like this. I had such with 180 mini pads
http://cgi.ebay.com/Dremel-200-1-21-...item4cf6467803
If you already have taken anodized layer or bought bare aluminum one you can go next level. You need piece of wooden slat with perfect edges and flat surfaces. Round wooden slat for round surfaces that you going to polish. You need wet sanding paper 320, 800, 1200 and 1500.
Start working with wet 320 and that is the key step. All the surfaces have to be flatten with that paper, all the big scratches during taking the anodized layer have to be removed now. If the scratch is in the middle of surface you have to take the entire surface down to remove it. If you will remove it only in that place it will not look good and the light will play there after polishing.
Sand as long as you will get sharp edges and scratches out. Surface must be smooth without any gouges. It’s a great time to think about live, universe etc. get some nice music. Of course you need water as well for wetting the sanding paper and drinking. Tell your wife you going on holidays.
When you will finish element with 320 go with 800, 1200 and then 1500 each one next goes quicker and easer then 320 which is the longest one.
If you finish get some good metal polish paste compound etc put it on microfibre cloth and polish for high gloss shine. The difficult areas you can do again with dremel and felt pads.
Try to do that by hand if you will do that by big machine you will lose your sharp edges.
I think it is all.
If you will work on bare aluminum I guess the step with 320 sanding paper will be much shorter. Depends on how the surface looks out from the aluminum cutting machine.
It is really not so difficult only time consuming process.
Huh now you gave me a difficult one too explain but ok lets try.
First of all if you plan to buy aftermarket aluminum fuel rails and you want to polish them yourself phone producer directly and get from him naked ones - bare aluminum. You will save a lot of time on taking out anodized coating.
If you already have anodized ones you have to take anodized layer away. It is almost impossible to do that by hand. Take a drill with sandpaper pads, 240 will be ok and take out the anodized layer carefully. You can do it only from big surfaces. You can mount a drill in a vice so the fuel rail will be in your hand during that process. Do not use big drill to remove anodized layer from small surfaces as you will quickly lose edges. The small areas you have to do with small mini drill and sand pads – you need dremel like this. I had such with 180 mini pads
http://cgi.ebay.com/Dremel-200-1-21-...item4cf6467803
If you already have taken anodized layer or bought bare aluminum one you can go next level. You need piece of wooden slat with perfect edges and flat surfaces. Round wooden slat for round surfaces that you going to polish. You need wet sanding paper 320, 800, 1200 and 1500.
Start working with wet 320 and that is the key step. All the surfaces have to be flatten with that paper, all the big scratches during taking the anodized layer have to be removed now. If the scratch is in the middle of surface you have to take the entire surface down to remove it. If you will remove it only in that place it will not look good and the light will play there after polishing.
Sand as long as you will get sharp edges and scratches out. Surface must be smooth without any gouges. It’s a great time to think about live, universe etc. get some nice music. Of course you need water as well for wetting the sanding paper and drinking. Tell your wife you going on holidays.
When you will finish element with 320 go with 800, 1200 and then 1500 each one next goes quicker and easer then 320 which is the longest one.
If you finish get some good metal polish paste compound etc put it on microfibre cloth and polish for high gloss shine. The difficult areas you can do again with dremel and felt pads.
Try to do that by hand if you will do that by big machine you will lose your sharp edges.
I think it is all.
If you will work on bare aluminum I guess the step with 320 sanding paper will be much shorter. Depends on how the surface looks out from the aluminum cutting machine.
It is really not so difficult only time consuming process.
4/13/11, 08:34 AM
Thanks for the kudos!
4/14/11, 07:59 AM
NTTAWWT
4/15/11, 02:08 PM
Bullitt Member
Join Date: August 8, 2006
Location: Good ole L.A.
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
So.... what's going on in here?
Where have I been?
Jed had I known it was your birthday, when we saw you at Fabulous Fords, we would have taken you out for drinks! Next time.
Where have I been?
Jed had I known it was your birthday, when we saw you at Fabulous Fords, we would have taken you out for drinks! Next time.
4/15/11, 11:51 PM
Legacy TMS Member
4/16/11, 06:23 PM
Bullitt Member
Join Date: August 8, 2006
Location: Good ole L.A.
Posts: 353
Likes: 0
Received 0 Likes
on
0 Posts
5/20/11, 10:31 AM
Legacy TMS Member
Join Date: May 24, 2006
Location: San Diego
Posts: 7,409
Likes: 0
Received 0 Likes
on
0 Posts
Black Mamba/Leo Update
The clutch packs along with some other stuff went south in the differential. So while they had her opened up I switched to 3.73's. Haven't had chance to get on it yet so no review at this time.
I recently purchased a condo so the Mamba has a garage once again.
Till next time.....
I recently purchased a condo so the Mamba has a garage once again.
Till next time.....
5/20/11, 10:50 AM
My update..
Chris is driving the Tacomobile daily. Recently hit 10k miles. It's no longer a GQ.
Chris is driving the Tacomobile daily. Recently hit 10k miles. It's no longer a GQ.
5/20/11, 10:56 AM
BoogieNights Studios:
Official Fluffer
Official Fluffer
Join Date: September 13, 2009
Location: Clarksville, TN
Posts: 5,520
Likes: 0
Received 5 Likes
on
5 Posts
Wow you guys actually live??
My update is I finally picked mine up from the guy I bought it from. If you wanna see it just go to Foxbody and look for the thread titled Boogienights
My update is I finally picked mine up from the guy I bought it from. If you wanna see it just go to Foxbody and look for the thread titled Boogienights
I'M GETTING A BLOWER (with attachments)
