Couple new mods coming
#1
GT Member
Thread Starter
Join Date: June 21, 2014
Location: Rowlett, TX
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
Couple new mods coming
Getting TB ported to 84mm at maxbore.com and getting a stand alone clutch reservoir.
Getting 84mm port job with low profile slim throttle blade shaft. 134$
Shelby iso clutch reservoir with motul rbf600 fluid coming as well.
This will max out my current setup without going headers.
Will get it dynoed after while. Made 395whp and 351wtq stock with aed tune.
Will return to same dyno
Current mods are:
Airaid intake
47# injectors
E85 flex fuel tune
MRT off road h pipe
Roush axleback
Exedy mach 500 clutch
Exedy lightweight billet steel flywheel
Ported tb to 84mm
Getting 84mm port job with low profile slim throttle blade shaft. 134$
Shelby iso clutch reservoir with motul rbf600 fluid coming as well.
This will max out my current setup without going headers.
Will get it dynoed after while. Made 395whp and 351wtq stock with aed tune.
Will return to same dyno
Current mods are:
Airaid intake
47# injectors
E85 flex fuel tune
MRT off road h pipe
Roush axleback
Exedy mach 500 clutch
Exedy lightweight billet steel flywheel
Ported tb to 84mm
#2
Legacy TMS Member
Originally Posted by tek302
Getting TB ported to 84mm at maxbore.com and getting a stand alone clutch reservoir.
Getting 84mm port job with low profile slim throttle blade shaft. 134$
Shelby iso clutch reservoir with motul rbf600 fluid coming as well.
This will max out my current setup without going headers.
Will get it dynoed after while. Made 395whp and 351wtq stock with aed tune.
Will return to same dyno
Current mods are:
Airaid intake
47# injectors
E85 flex fuel tune
MRT off road h pipe
Roush axleback
Exedy mach 500 clutch
Exedy lightweight billet steel flywheel
Ported tb to 84mm
Getting 84mm port job with low profile slim throttle blade shaft. 134$
Shelby iso clutch reservoir with motul rbf600 fluid coming as well.
This will max out my current setup without going headers.
Will get it dynoed after while. Made 395whp and 351wtq stock with aed tune.
Will return to same dyno
Current mods are:
Airaid intake
47# injectors
E85 flex fuel tune
MRT off road h pipe
Roush axleback
Exedy mach 500 clutch
Exedy lightweight billet steel flywheel
Ported tb to 84mm
#4
Legacy TMS Member
Originally Posted by tek302
Dyno jet, giant in ground cylinders
#5
GT Member
Thread Starter
Join Date: June 21, 2014
Location: Rowlett, TX
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
Im hoping to hit 430whp next visit
#6
Legacy TMS Member
Originally Posted by tek302
395whp was stock besides a tune.
Im hoping to hit 430whp next visit
Im hoping to hit 430whp next visit
#7
GT Member
Thread Starter
Join Date: June 21, 2014
Location: Rowlett, TX
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
#8
Legacy TMS Member
Originally Posted by tek302
Good luck!
#9
GT Member
Thread Starter
Join Date: June 21, 2014
Location: Rowlett, TX
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
frpp boss 302 springs
bmr rear lower arms
bmr rear lower relocation brackets
bmr adjustable pandhard bar
roush upper arm
#12
2013 RR Boss 302 #2342
Join Date: March 6, 2012
Location: Lancaster, PA
Posts: 11,667
Likes: 0
Received 2,174 Likes
on
1,621 Posts
Originally Posted by tek302
Car made 438whp and 391wtq
#13
Roush Forum Stalker
Nice!
Gained about 40HP from the porting! Did you need a new tune as well?
Gained about 40HP from the porting! Did you need a new tune as well?
#14
GT Member
Thread Starter
Join Date: June 21, 2014
Location: Rowlett, TX
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post